TFX30PBZABB General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Harold from Concord, CA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Frost in and around ice maker outlet
Followed the video directions. Spent about 5 minutes and I was done. Very easy to do. Problem with frost is gone. The video makes it easy to remove the plastic parts without any damage.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from Little Elm, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Frost buildup in the freezer near the ice chute.
I watched the video on the PartSelect.com website and decided to give it a try. The replacement of the flapper was even easier than I anticipated! The old flapper was extremely warped and was allowing air into the freezer. I'm not sure how/why it was in that condition but I am happy to report that I have no more ice buildup. Thank you, PartSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Theresa from Grand Blanc, MI
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
We had ice crystals on the ice tray and door
Removed the ice maker control panel and accessed the flapper door, easy switch out for new door and seal. The 2 year old warped seal didn't close and so ice crystals formed in the freezer - new unwarped part and Ta-Da no more problems :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ray from Fredericksburg, VA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Air leaking into freezer through door dispenser
I followed the video instructions. They were clear and consise. I removed the trim ring and controls. Them removed the housing and flapper. I did notice a small burr in the plastic chute and foam insulation. I trimmed this off with a utility in hopes this burr caused the flapper to warp. This is the 2nd time the flapper has been replaced in 1.5 yrs. The repair was really easy thanks to the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Ft Myers, FL
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
air leak from ice maker flap permitting frost buildup inside ice maker dispenser
Watched à video provided at your website. Removed te cover then removed 4 screws holding the control panel' snapped out the old flap and inserted the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wanda from Katy, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The rubber seal on the flapper came off.
My husband made the replaced the flapper while watching the video provided in your email, it was easy. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebecca from Banning, CA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
ice dispenser frosting up
Watched the video from your site and followed instructions, extremely easy after that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eti from Milwaukee, WI
- Parts Used:
- WR57X10006
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
the part was leaking, and we had to disconnect water supply to the fridge. The ice-maker was disabled
We replaced the part, and fixed the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steven from westminster, MD
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door ice dispenser flapper warped/frost build up
I followed the repair video Partselect provided online. It the repair easy and fast. Great video!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GENE from ASHEBORO, NC
- Parts Used:
- WR62X23154, WR62X26536, WR62X26536
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
No cube ice. We had crushed ice.
Removed ice select control unite from freezer by removing 3 nut screws holding unite in place. Disconnect 2 electrial plug ins.Remove unite from freezer and place on table for easy work space. Remove 4 nut screws holding Solenoid & Arm. Replace with new Solenoid & Arm. Reinstall back in freezer and now we have cube ice again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kay from Lehigh Acres, FL
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Flap on door not closing and frost build up on dispenser
Followed video. Changing flap was not difficult but did not fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Charlotte, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Misting inside freezer which blocked the ice dispenser.
I followed the video instructions to the letter and it was very easy and a total success. I believe I would have had problems but for thr video demonstration which was very clear and straight forward in a simple manner. Thanks for the prompt delivery of the part and the help installing it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Nags Head, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
flapper was locking open periodically.
Replaced flapper, which was in surprisingly good condition. Major part of repair was removing a lot of mold incurred from long term seepage of room air into the ice channel. In the process of the repair, I discovered that the solenoid to the right of the flapper was hanging up badly. I removed it and cleaned both the plunger and the interior cone of the solenoid with alcohol. This removed quite a bit of rust and some mold. Reinstalled solenoid, replaced flapper and it works just fine. May need to replace solenoid if problem recurs. Certainly worth $37.00!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeanne from Amissville, VA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Flapper became warped. Freezer /icemaker frosting up... ice melting and sticking.
Popped off the front frame and front of mother board. unscrewed the assembly to be able to lift up to get to flapper. Lifted it up out of the the way ( wires are attached so it may take one other person to hold it up out of the way). Pop out the old flapper and replace with new one. Easy !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Kennesaw, GA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The ice dispense door flapper was deformed letting warm air into the freezer compartment.
The trim piece covering the opening of the dispenser is the first and most difficult part of the disassembly. Take care when removing this piece that it does not break.
Was this instruction helpful to you?
Thank you for voting!