TFX27PPZBAA General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- JAMES R. from INDIAN SHORES, FL
- Parts Used:
- WR17X11653
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Moisture seeping into freezer through ice dispenser
Removed ice dispenser trim from bottom-up and then removed control panel by gently pulling up from the bottom. Removed four screws holding dispenser chute and then two screws holing flapper assembly. Replaced gnarly old flapper with a new one and put all removed pieces back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Corpus Christi, TX
- Parts Used:
- WR17X4312
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replace oxidized auger and Ice bucket assembly
Very simple replacement of complete assembly. I debated replacing individual parts that would have taken considerable effort. Ordered the complete assembly and it was simple to replace.Removal of face plate by removing two Philips screws and reusing them to hold face plate on. Jim
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Lewis Center, OH
- Parts Used:
- WR71X2494
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Frame Was Broken
Took off metal brackett, removed plastic frame and installed new plastic frame.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronnie from Borger, TX
- Parts Used:
- WR17X4312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Icemaker stopped working
Ordered new ice bucket w/auger. All I had to do was change out the cover (four screws). Easy repair; works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from Franklin, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The door recess asm would not seal tightly
remove the 'pop-out " frame around the door recess, you pry the flexable seal from around the ice despenser, have someone hold the unit with the wiring, remove the one screw that holds the door recess, and replace the new one. reverse the procedure. remember to unplug thr frig. first
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from milford, CT
- Parts Used:
- WR30X256
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken ice bucket
Very easy to repair-Went online-Found diagrahm-Ordered part-and presto it was fixed.
Very good schematic to go by. If you can read you most likely can fix it.
Very good schematic to go by. If you can read you most likely can fix it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- laddie from benton, KY
- Parts Used:
- WR57X10007
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
cracked valve body
swapped new valve for cracked valve, after marking water lines to which side of the old valve they were on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lawrence from new haven, KY
- Parts Used:
- WR17X4358
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
water tank was leaking
really simple,take 2 nuts loose pull the hose out and then replace.took less than 30 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Dallas, TX
- Parts Used:
- WR17X4341
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Auger was rusty
Easy to take apart just keep track of all your screws and parts most inportant of all are the 3 claw like and spacers that are inside the clear round part at the end of the ice bucket these pieces only turn in one direction if you put them on backwards or in the wrong order you will tear up your ice bucket so pay close attention when taking it apart and reassembling it. One think that might be helpful is to take some pictures of the ice bucket before disassembly something i wish i had done prior to taking it apart. Some people download instructions off the internet but i felt like i could do it with out help well good luck
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Joliet, IL
- Parts Used:
- WR62X23154
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Ice maker- wouldn't release cubes only crushed ice.
Really easy- turned off ice maker, powered down appliance briefly. Removed ice maker by removing 3 screws with 1/4 nut driver. Unplugged ice maker from power supply. Removed and replaced solenoid arm assembly. Reversed steps and whammy - ice cubes dropped.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold E. from Hartselle, AL
- Parts Used:
- WR17X3095, WR17X10282
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
seal deteriotated preventing flappper from fulling closing, allowing escaping air to freeze up water line.
Snapped off the plastic plate covering the dispenser. Removed the four screws holding the mechanism in place. Remove the electrical connections. Pull the mechanism out and up carefully pulling the dispenser pad out with all the mechanism in place. Look at the mechanism before removing any parts to get a mental image so that reassembly will be easy. Remove any electrical switch or circuit boards and remove old parts before submerging the mechanism in hot soapy water for clean-up. The Clean-up will take longer than the disassemble and reassembling. After completion the dispenser works as it should.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kay from Lehigh Acres, FL
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Flap on door not closing and frost build up on dispenser
Followed video. Changing flap was not difficult but did not fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eti from Milwaukee, WI
- Parts Used:
- WR57X10006
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
the part was leaking, and we had to disconnect water supply to the fridge. The ice-maker was disabled
We replaced the part, and fixed the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steven from westminster, MD
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door ice dispenser flapper warped/frost build up
I followed the repair video Partselect provided online. It the repair easy and fast. Great video!!!!
Was this instruction helpful to you?
Thank you for voting!