GTS22ICSARBB General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from Island Lake, IL
- Parts Used:
- WR55X10025
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
frige too cold
changed sensors did not repair problem,replaced damper with mechanical damper fixed problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Guojie from Gainesville, FL
- Parts Used:
- WR60X10220
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
noise from the condebser fan moter
Just follow the instructions from the Youtube, the link to the video is included in the sheet coming with the part. It was easy to take the entire compartment out as instructed, however, after replace the old motor with the new one, it took more than 20 min to put the entire compartment back after trying different ways. It has been working greatly since it was repaired.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryan from Las Vegas, NV
- Parts Used:
- WR60X10220
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
condenser fan was noisy ( squeaking)
Not knowing anything about a refrigerator it was hard to find the source of the noise. Once I could isolate it we googled the appliance repair and found the video from Parts Select and the rest was a piece of cake. Saved a service call and bloated parts prices. Thank you Parts Select!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Troy from Dacula, GA
- Parts Used:
- WR55X10025
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Food section of fridge always warm
Located temperature sensor on condenser in the freezer section( as per instructional video ). Cut off bad sensor with wire cutter then soldered on the new sensor and sealed with electrical shrink wrap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from Lubbock, TX
- Parts Used:
- WR60X10220
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Fan wasn't running and walls of freezer and ref. were hot
took screw that holds motor frame in place out with nutdriver, rolled motor frame out after unplugging motor,took screw out of strap that held motor in frame, removed bushings from old motor and put them on the new one and re3versed the proceedure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John J. from Deland, FL
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
freezer no cold enought
as per video- follow all of the videos and u r going to save a lot of money tx partselect im glad I found u guys ps only order from partselect.com they only ship the correct parts remember look at the video select the symptom and buy as per video tx again problemsolved
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Rockwood, TN
- Parts Used:
- WR55X10025
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Would not self defrost.
Remove the shelves then remove the back by removing the two screws at the top of the panel. Locate the temperature sensor on top of the coil. Cut the wires and replace with the new one. Use wire nuts and electrical tape to reconnect the wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- chol from Glenview, IL
- Parts Used:
- WR55X10025
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
refriger warm
replace sensor in refriger.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Altoona, IA
- Parts Used:
- WR60X10220, WR07X10055
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
the fan motor wouldn't run and the refrigerator wouldn't cycle.
Unplugged refrigerator and removed rear cover. Removed the two attaching cap screws from the mounting bracket. Removed fan blade by sliding it off the shaft, disconnected wiring plug and removed the motor. Removed the rubber grommets from the old motor and installed on the new unit. Set the new unit in place and reinstall the fan blade, mounting bracket and screw into place. Reconnect the wiring harness. To replace the relay, simply remove the wire clip from the relay cover, slide the relay off the connecting pins on the compressor and disconnect the wires. Slide the new relay into place, reconnect the wires and replace the cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PHILIP from JACKSONVILLE, FL
- Parts Used:
- WR57X10086
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
ice maker would turn on to allow water into ice tray and would shut off. water would over flow, eventually out of the freezer
replaced the icemaker inlet valve. works like a champ now
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marco from Fallbrook, CA
- Parts Used:
- WR55X10025
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
My fridge was colder than my freezer
I can't tell you how luck I feel after finding your website I ordered the temperature sensor after watching one of your videos on-line and the repair went just as on the video. I pulled the "bad" sensor out, and replaced it with the new one. Keep in mind that this is the first time I ever touch an appliance, needless to say I'm feeling pretty good about that! All in all it took me about 20 minutes to complete my repair and it now has been about 4 days and the refrigerator is working like new again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from castle rock, CO
- Parts Used:
- WR60X10220
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Fan Sqeels
Remove back panel . Removed fan shroud. Replaced fan and panel. Ops ck ok so far
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from myrtle beach, SC
- Parts Used:
- WR57X10086
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
ice maker not making ice
I looked up appliance on internet,diagram only showed the inlet valve and ice maker in schematic.I ck'd to see if water was getting to valve(it was)but wasn't getting to ice maker,thus I replaced the valve and it solved the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from Brentwood, MD
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench set
freezer and refrigerator wasn't cold
Replaced all the sensors in both the feezer and refrigerator.Even though it colder now it still is not cold enough.Freezer won't freeze items but is cold and refrigerator still not real cold
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- thomas from albany, NY
- Parts Used:
- WR23X10334, WR09X10104, WR02X11567, WR01X10220
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
frig ran to often
took apart stat. area rplaced wire harness &t.stat simple but im a retired union electrican so wiring was a bit easy
Was this instruction helpful to you?
Thank you for voting!