TPX24PBZABB General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Harold E. from Hartselle, AL
- Parts Used:
- WR17X3095, WR17X10282
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
seal deteriotated preventing flappper from fulling closing, allowing escaping air to freeze up water line.
Snapped off the plastic plate covering the dispenser. Removed the four screws holding the mechanism in place. Remove the electrical connections. Pull the mechanism out and up carefully pulling the dispenser pad out with all the mechanism in place. Look at the mechanism before removing any parts to get a mental image so that reassembly will be easy. Remove any electrical switch or circuit boards and remove old parts before submerging the mechanism in hot soapy water for clean-up. The Clean-up will take longer than the disassemble and reassembling. After completion the dispenser works as it should.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Spring, TX
- Parts Used:
- WR62X23154
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Refrigerator was only dispensing crush ice and not cubes
Solenoid pushing the crushed ice flapper was burned out. Solenoid was easy to find unplug and replace. I used the old piston which simplified things. Now works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luis from Chester Springs, PA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Flapper was warpped
Follow instruction on the video you provided
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Dumfries, VA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Flapper valve allowing frost/ice to accumulate in chute in summer
Followed the online video exactly and it was easily done. Couldn't have been better. The problem is solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Fripp island, SC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
3rd Flap for this Ice Mkaer, keeps warping
Very Easy, follow direction I the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Kennesaw, GA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The ice dispense door flapper was deformed letting warm air into the freezer compartment.
The trim piece covering the opening of the dispenser is the first and most difficult part of the disassembly. Take care when removing this piece that it does not break.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Theresa from Grand Blanc, MI
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
We had ice crystals on the ice tray and door
Removed the ice maker control panel and accessed the flapper door, easy switch out for new door and seal. The 2 year old warped seal didn't close and so ice crystals formed in the freezer - new unwarped part and Ta-Da no more problems :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeanne from Amissville, VA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Flapper became warped. Freezer /icemaker frosting up... ice melting and sticking.
Popped off the front frame and front of mother board. unscrewed the assembly to be able to lift up to get to flapper. Lifted it up out of the the way ( wires are attached so it may take one other person to hold it up out of the way). Pop out the old flapper and replace with new one. Easy !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Glendora, CA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Inside freeze was frosting up
used a flat screwdriver to pop off out side cover then remove 6 screws took off plate. Pulled off the flapper and replaced. less the 15 mins and fixed the issue
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Austin, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Heavy frost was forming where ice is dispensed
Watched the PartSelect video. Very simple and solved the problem. Very pleased with the repair and PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CARY, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker was frosting and the dispenser chute was clogged with frost
I followed the directions on the video. Although my dispenser was a little different, I was able to get to the faulty door in less than five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gordon from Pittsburgh, PA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Flapper Seal for Ice Cube Chute was Warped and would not close tightly.
I followed the instructions on the video presentation, stopping the video each time until I had completed the described step. Only one minor change from the video...my refrigerator door (stainless steel) does not have the plastic edging around the control panel as shown in the video. It took me a minute or two to figure out that I had to push the tabs on the bottom of the control panel. The rest was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Concord, CA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Frost in and around ice maker outlet
Followed the video directions. Spent about 5 minutes and I was done. Very easy to do. Problem with frost is gone. The video makes it easy to remove the plastic parts without any damage.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Pittsboro, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The flapper on the freezer was warped and allowed humidity to create frost in the freezer.
I watched the how to video and followed the instructions. The entire repair took less than 4 minutes. Hardest thing was disconnecting the control panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THEOTIS from CHARLOTTE, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Refrigerator COnstant running and low ice output
I followed the instructions on the youtube video on the company web page. I removed the cover by hand, removed the exisitng flapper door and install the new door, easy as pie.
Was this instruction helpful to you?
Thank you for voting!