TFX22JRXAAA General Electric Refrigerator - Instructions

Super simple! Hardest part of the entire process was identifying which part I needed to order. Once I received the part (which shipped promptly and was at my front door within 2 days), all it took was 5 mins and a screwdriver and I was back to having a usable snack drawer!

Turn off power
Remove operator faceplate by pullling out on outer lower corners
Disconnect wire connectors from circuit board
Remove four screws from dispenser and pull out dispenser assy
Replcae Door ASsembly
Put everything back in place
Power up
Job Done

Found a step by step video on YouTube made replacement very easy. Cubed ice is back. Time for a cocktail to celebrate!

Determined that the little door that opens to allow full size cubes to fall was not opening. If you open freezer door, hold door switch in, select cubes and push in the lever that the glass pushes in you should hear the solenoid lift open which opens the little door. Mine was doing nothing. Removed ice bin and then removed icemaker motor/solenoid section from back of freezer by disconnecting two wire harnesses and one screw. Found that solenoid smelled burnt and could see that inside of the solenoid was swollen out of round and burnt. Simple to replace.

Thanks to the stories on PartSelect my wife and I knew what to expect. The biggest hassle was sawing off the rivet that's on the hinge on the refrigerator (my wife volunteered for that job). When we got everything back together the door worked a lot better, but still wouldn't close without a little push. In frustration and running out of time, we put the stuff back inside the refrigerator door and that did the trick! The weight was enough to allow the door to close on its own.

I used a block of wood to hold up the door. Then unbolted the lower hinge from the fridge. That is when I found out that it was fine and it was the upper half of the hinge that was broken (worn).
So I unbolted the upper hinge (mounted on the bottom of door) It uses the same part. So I installed the part on the upper half of the hinge.

I wish somebody would have told me that you need 2 of these for each hinge. The bottom one was in good shape, lucky for me.

Replaced dispenser flapper

First, I had to remove the face plate where the ice and water was dispensed remove 4 screws holding the electrical circuits, disconnect circuits ,remove 2 screws holding soleniod and one screw holdin crank assembly. repace parts and screws.

There was what seemed to be a half chewed up washer under the refig. door. The door wasn't closing all the way. DING!! Something was wrong!!

I looked up your schematic for the refrig door and decided what piece might have broken. It was a good guess and the part showed up a few days later.

I wedged up the refrig door to take the tension off the lower bracket. Then, just took off the bracket and replaced the broken door closing cam.

removed top plate and raised the door off. I removed the L bracket from the fridge then noticed the part was rivited onto the L bracket. I cut the rivit and replaced the cam and used a small bolt and nut to sdecure it. Replaced the L bracket, the door, and the upper support. Only problem was the surprise rivit

1. I removed the top door hinge.
2. I removed the door and laid it flat.
3. I replaced the cam attached to the bottom of the door. This was very easy.
4. I removed the bottom door hinge and had to remove the brad that held the second cam. This went well as I was able to saw it with a hacksaw.
5. Replaced the second cam with a bolt and nut.
6. Replaced the door and top hinge.
7. Remember to order two cams when you do this repair.

Removed screws holding top door hinge. Lifted the door off bottom hinge. Unscrewed cam from bottom of door. Drilled out rivet holding the second cam in the bottom hinge. Replaced both cams using a flat headed bolt to hold the bottom cam. Dropped door into bottom hinge and replaced top hinge screws. Job done.

Make sure you buy two cams and have a bolt to replace the bottom rivet.

Not a difficult job as long as you have a drill !!!

Why don't they just tell you that you have to buy 2 cams. I have now replaced the cams on both doors. The other door broke about 4 years ago. Fortunately the first time I read the user commetns or I would've bought just one. It is a quick easy fix. The longest step is drilling out and replacing the rivet. Everything else is done with a nut driver.

Replaced the old cams with new ones, door works perfect now.

Thought I would only need one when I looked at the picture of the parts. Decided to order two just in case and after taking it apart both were broken. Needed two.
Took the top door bracket off and lifted the door off of the bottom bracket. Re-assembled cams, put a little white grease on all moving parts, placed the door into bottom bracket and installed top bracket. Adjusted top bracket to make door line up with edge of refrigerator and all is well.