GTS22JBPARCC General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jesse from Kingman, AZ
- Parts Used:
- WR50X10068
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Frost build up on coils
Removed shelves and light bulb. Undid the two screws on the back panel with nut driver. Snipped the two wire leads to the defrost thermostat. ( orange and pink wires) Carefully removed the defrost thermostat from the coil. Stripped both ends of the wire leads about a half inch and onnected with two wire nuts. Then wrapped with electrical tape to seal from moisture. Carefully attached defrost thermostat to coil. Screwed the back panel back on. Reinstalled light bulb and shelves. And plugged refrigerator back in. Works like a charm. Saved close to 100.00 dollars doing repair myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from tulsa, OK
- Parts Used:
- WR50X10068, WR55X10025
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Ice melting and refreezing
Defrost cycle staying on too long causing ice to melt, refreeze and seizing up ice maker. Replaced temp sensor and defrost thermostat just to be sure. Fixed the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TREVOR from KENT, WA
- Parts Used:
- WR72X10072
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
broken slide drawer track
Took out shelf, unscrewed old track, screwed on new track. Only thing is not a standard flat or Phillips screw head so if you don't have a star head bit, you are out of luck.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Zachary from Decatur, GA
- Parts Used:
- WR55X10025
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Fridge was freezing food near the back, adjusting internal temp not fixing the problem
Unplugged the refrigerator first....then on the inside of the fridge, I popped the temp sensor cover off (upper LH side) and exposed the old sensor. I snipped off the old sensor about 3" down from the end and connected the new sensor (which I trimmed down to about 3" long) with some heat shrink wire nuts/connectors. Let the fridge run for a day or so and confirmed the problem was solved! Oh yeah, there was no way to tell the 2 wires apart (power vs. ground) on the sensor. However there was a manufacturer's stamp on the wires. So note the orientation of the text and mark one of the wires with a sharpie on both the old and new sensor before trimming. This will give you a reference for which wires to connect when adding the new sensor to the old wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from Burke, VA
- Parts Used:
- WR72X10072
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The plastic piece that holds the screw in on the pan of the refrigerator had broken
I took the pan out, replaced the bar with the new part - slide pan RH - and I was back in business. It couldn't have been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from Whittier, CA
- Parts Used:
- WR50X10068
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
fridge and freezer not staying cold
removed back panel from freezer. located thermostat removed and replaced thermostat put panel and all baskets back into freezer and plugged fridge back in. Works perfect problem solved
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- philip from cocoa, FL
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
freezer would not defrost
There were only 3parts listed to check omed out the defrost heater and thermostat ....thermistor checked bad ordered replacement took less than 2 minutes to replace after I defrosted it again runs fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Orlando, FL
- Parts Used:
- WR50X10068
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
refrig not turning off and defrosting
replaced the defrost thermostat. The "how to" video was superb. Watched it twice before beginning the job. repair went as described.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Saint Charles, IL
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
refrige ws too cold
as per video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- khampheuy from Kerrville, TX
- Parts Used:
- WR50X10068
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Frige was warm and Freezer was freezing up
I have checked the defrost thermostat:During the defrosting cycle the thermostat is still open
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Brooklyn, NY
- Parts Used:
- WR72X10072
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Guide rail cracked
My snack tray guide rail cracked and this was the easiest repair I've ever made.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ELIZABETH from BOULDER, CO
- Parts Used:
- WR72X10073, WR72X10072
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
shelf brackets holding meat/cheese drawer cracked.
I unscrewed two brackets on each side (Had to buy the correct little screw driver) and screwed in the new ones.Easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JULIA from WARWICK, NY
- Parts Used:
- WR72X10073, WR72X10072
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Socket set
Left Slide Pan Broke Off, Needed To Replace It
Remove entire shelf from refrigerator and removed broke, set the replacement part in place, screwed it in and it worked perfectly, done infive minutes. Took me longer to take out the self that to do the replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Jamestown, ND
- Parts Used:
- WR72X10072
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Slide track on right side of chill tray, where it was held together, on the metal frame, the screw cracked the plastic.
Went to Sears, where I bought the Fridge, they could not locate the part I needed, so I went on line, and found partselect.com, entered the proper information, found the part I needed fast, ordered the part, received it in two days time, I already had the old part off, so it took less than ten minutes to replace it with the new part, works great, the people at partselect.com were great, an if needed, I will gladly order from them again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Rancho Cordova, CA
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator freezing.
Temp. Sensor was under an egg shaped cover on the left side wall in the refrigerator. Remove the cover, cut the two wires to the old sensor and remove it. Connect the new sensor to the two wires using butt connectors. Replace cover and done.
Was this instruction helpful to you?
Thank you for voting!