ETS22XBPARBB General Electric Refrigerator - Instructions

Located temperature sensor on condenser in the freezer section( as per instructional video ). Cut off bad sensor with wire cutter then soldered on the new sensor and sealed with electrical shrink wrap.

as per video- follow all of the videos and u r going to save a lot of money tx partselect im glad I found u guys ps only order from partselect.com they only ship the correct parts remember look at the video select the symptom and buy as per video tx again problemsolved

Removed the panel on the back wall inside the freezer side. To do this I unplugged the appliance, removed the racks, drawer, bulb and two screws holding the panel in place. The defrost cycle was not working so ice buildup on the coil was to the point of blocking air flow to the refrigerator side. I used a hair dryer set on high and stuffed two towels at the base of the coil to collect the melting frost and ice. Once the coil was clear of frost and ice I took the defrost timer off by sliding the clip off the tube, cut the wires and stripped the ends so I could use wire nuts to make the new connections . Placed the new defrost timer in the clip and reattached in the same location the old one was removed from. The sensor was replaced by doing the same steps. I replaced the panel after all the wire nuts were secured and the wires were tucked away where they would not interfere with the fan. Replaced the bulb, drawer, racks and food and plugged The refrigerator back in. 20 minutes from beginning to end.

removed shelves and rear panel. cut wires, spliced in new part used wire nuts and filled wire nuts with silicone, replaced back panel and shelving

I can't tell you how luck I feel after finding your website I ordered the temperature sensor after watching one of your videos on-line and the repair went just as on the video. I pulled the "bad" sensor out, and replaced it with the new one. Keep in mind that this is the first time I ever touch an appliance, needless to say I'm feeling pretty good about that! All in all it took me about 20 minutes to complete my repair and it now has been about 4 days and the refrigerator is working like new again!

per your instructions

I called angies list to get a name of a repair person . We were having very hot weather and I did not want my freezer food to spoil. The cost was not bad for the look see $127.00 plus parts and labor added on to this. I decided to look on the internet and found your services and the video on how to replace the part that might be bad. I bought a new thermostat and also a sensor and added the control board as the refrigerator is 13 years old. I spent a total of $206.00 and did the work myself so no labor cost. I was so happy as a new refrigerator like this one would be $3100.00 plus tax. Thank You R. Polglase

took out shelves and removed the back plate my removing 2 screws with a nutdriver.removed the old defrost timer and defrost heater which was really easy.then installed the new ones.the video i watched on the website was really helpfull.

changed sensors did not repair problem,replaced damper with mechanical damper fixed problem.

Remove plastic parts then remove back panel, remove plastic seround holding motor, romove 2 screws holding motor bracket, unplug motor, reinstall motor, bracket, seround, back panel DONE

removed the inside fridge electrical panel and swapped switches

easy pry out, disconnect wiring, connect on new switch and press in switch.

It was very tricky getting the old piece out, even though it was partially broken... I ended up snapping the old piece to remove it. Trying to install the new track with the glass shelf above was not working at all, but once I removed the glass shelf above it, the new piece went in pretty easily. With the glass shelf out, I could angle the track upward to get it into position. In retrospect, I should have removed the glass shelf from the start... it would have made removal of the old piece much easier.

We just pried off the fan blades and pushed on the new part. Could not have been easier. The rat has been permanently dipatched and, hopefully, that is that.

Unplugged the refrigerator first....then on the inside of the fridge, I popped the temp sensor cover off (upper LH side) and exposed the old sensor. I snipped off the old sensor about 3" down from the end and connected the new sensor (which I trimmed down to about 3" long) with some heat shrink wire nuts/connectors. Let the fridge run for a day or so and confirmed the problem was solved! Oh yeah, there was no way to tell the 2 wires apart (power vs. ground) on the sensor. However there was a manufacturer's stamp on the wires. So note the orientation of the text and mark one of the wires with a sharpie on both the old and new sensor before trimming. This will give you a reference for which wires to connect when adding the new sensor to the old wires.