TFT25PRYDAA General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Thomas from Arlington Heights, IL
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Frost on the bottom of the ice bin frome warped rubber flapper
Pulled the outter cover off, removed the electronic board, replaced the flapper and put it back together again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Atlanta, GA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Frost was building up inside the freezer just above the ice dispenser shute.
Followed the instructions and replaced the door recess.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HERBERT from Harlingen, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
gasket was shot
took off the panel, took out 4 screwws, took out old flap, installed new flap, put screws back in , and put trim back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from zion grove, PA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
rubbeer flapper was worped causing frost in the freeze
The same as the vidio, very easy. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Lewis Center, OH
- Parts Used:
- WR71X2494
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Frame Was Broken
Took off metal brackett, removed plastic frame and installed new plastic frame.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from Franklin, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The door recess asm would not seal tightly
remove the 'pop-out " frame around the door recess, you pry the flexable seal from around the ice despenser, have someone hold the unit with the wiring, remove the one screw that holds the door recess, and replace the new one. reverse the procedure. remember to unplug thr frig. first
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from milford, CT
- Parts Used:
- WR30X256
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken ice bucket
Very easy to repair-Went online-Found diagrahm-Ordered part-and presto it was fixed.
Very good schematic to go by. If you can read you most likely can fix it.
Very good schematic to go by. If you can read you most likely can fix it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lawrence from new haven, KY
- Parts Used:
- WR17X4358
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
water tank was leaking
really simple,take 2 nuts loose pull the hose out and then replace.took less than 30 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Novi, MI
- Parts Used:
- WR17X11349, WR17X4358
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
My despenser water reservoir leaked at the seam, causing water to alway puddle at the bottom of the inside space
I had read from your sight, to simply cut the lines at the reservoir and tape the new lines to the old. Then use the old lines to pull/feed the new lines to the coupler/valve. This worked great and greatly decreased the time it took to install. I spent more time moving out the frig and cleaning up all the dust (probably should do that more often)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold E. from Hartselle, AL
- Parts Used:
- WR17X3095, WR17X10282
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
seal deteriotated preventing flappper from fulling closing, allowing escaping air to freeze up water line.
Snapped off the plastic plate covering the dispenser. Removed the four screws holding the mechanism in place. Remove the electrical connections. Pull the mechanism out and up carefully pulling the dispenser pad out with all the mechanism in place. Look at the mechanism before removing any parts to get a mental image so that reassembly will be easy. Remove any electrical switch or circuit boards and remove old parts before submerging the mechanism in hot soapy water for clean-up. The Clean-up will take longer than the disassemble and reassembling. After completion the dispenser works as it should.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from Benton, AR
- Parts Used:
- WR17X11653, WR17X3489
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Flapper would not seal. Shield broken
Followed on line instructions. No problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ERIC from DAYTON, OH
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Frost on inside of freezer.
Since my refrig is 18 yrs. old and I never had to replace it, took a little long to remove trim piece on the outside. After that repair went smoothly. I still have problem with water collecting inside on the bottom of the freezer, might have a leak somewhere. Ice maker is functioning correctly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Bridgewater, NJ
- Parts Used:
- WR17X3089
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Ice dispenser had a transistor failure on the control board
The solenoid in the dispenser was overheated due to the control board failure. After I rerplaced the board I found the heat had distorted the plastic crank and jammed the solenoid action. The plastic crank was easy to replace. Now after expending approx. $75 everything works normally!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- alfred from holyoke, MA
- Parts Used:
- WR17X4358
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable), Wrench set
pinhole leak in water resevoir
pulled fridge away from wall, shut water to fridge disconnected both lines,back one and front one.Removed old water resevoir 1 screw. cut old lines at resevoir. used small threaded rod (1"long)to connect old lines to new lines and taped together,pulled new lines with old lines and reconnected.No lifting of fridge,actual repair under 1 Hour but took longer because I cleaned underneath really well and took my time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Saint Johns, FL
- Parts Used:
- WR17X11653
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Frost in ice dispensor
Had to take front panel off dispenser area. Then remove components and install new part. That was easy part. Problem was getting components back into front of freezer. Seemed like something was blocking it from going all the way in. Had to remove small amount of insulation and "jiggle" components and eventually fell into place.
Was this instruction helpful to you?
Thank you for voting!