TBX18NIZURWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Verma Jean from Lincoln, CA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
my ice maker quit working
I watched the video from the link that was sent to me with the shipping notice. It was very easy to understand. I had no trouble at all. I'm 75 years old woman, however, and I can fix about anything. Don't be afraid to fix appliances yourself if you feel you have the knowledge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Horseshoe Bay, TX
- Parts Used:
- WR30X10093
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker leaking
Quite easy. Turn off water supply and turn off ice maker at switch inside freezer. Unscrew the old unit, separate the electrical connection, and pull it out. New unit comes with parts that do not fit my refrigerator, so visually examine the new and old units, reuse any needed parts from the old unit, such as plastic water ramp. Reconnect the electrical connector, and screw it back in. Turn water supply back on and then turn ice maker back on at switch inside freezer. Discard unused parts. Wait up to 24 hours for new ice cubes to be made.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacob from Waggaman, LA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No ice!
Literally took out one screw and a wiring harness. Removed the old plastic piece off of the old ice maker and put on the new one.Installed new ice maker with the one screw and plugged the wiring back in.DONE!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mitchell from Chicago, IL
- Parts Used:
- WR30X10093
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
The Ice Maker stopped making Ice because the arm over the ice bucket which turned turned on the icemaker was broken
I read the step by step instructions that came with the part. I turned two screws and disconnected the electrical harness and Removed the icemaker. Two other parts from the old icemaker were easily removed without any tools and put on the new icemaker. The new icemaker was put in the same way the old one came out. I reconnected the electrical harness and tightened the old screws. The hardest part of the whole job was reading the directions. They were easy to follow if you take the time to Just read them!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert jr from east rutherford, NJ
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Frig was not making ice.
Removed the faulty ice maker in about two min.. New unit was installed in approx. five min. Watched your video prior to installation and it helped greatly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from Owensboro, KY
- Parts Used:
- WR71X10080
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Retainer Bar bend
Removed the bent bar and the end clips. Attached the end clips to the new retainer bar and snapped into place on the refigerator door. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Reading, MA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No ice.
Piece of cake and now I get loads of ice.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Garry from San Antonio, FL
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
ice maker not working
unscrew one screw unplug.insert the ice maker,put the screw back in you have ice less than ten minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from San Tan Valley, AZ
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ice Maker stopped working
Took out one hex screw, disconnect electric couplings, pulled original ice maker out and found that the water supply line to the ice maker was frozen solid as well as the shute cup. Used hair dryer to thaw out the line and the cup reinstaled old ice maker and it worked fine. Did not have to use the new part at all at this time. Am keeping new part for future use.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Wildomar, CA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Old Icemaker Stopped Making Ice
Instructions that came with the part were useless. I would have created new problems if I had attempted to follow the instructions. However, once I had the old part removed and put it beside the new part, required repair process was obvious, easy and quick. Frig now makes ice better than it ever did.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Pampa, TX
- Parts Used:
- WR30X10093
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ice maker was leaking
Watched the video that showed how to disassemble the ice maker. Then went right in and replaced the part and turned it on. It immediately started filling up the ice tray. I still have not been able to find out why it does not make as fast as the original ice maker. The tempeature for the freezer is set pretty cold.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lani from Lakeside, CA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ice maker made no ice and no water from dispenser.
After what I thought was a thorough troubleshooting of said problem I replaced the Water Valve Assy which was really easy as the video shared, but it did not fix my problem. I had forgotten to pull the water line apart at the coupling below the doors (this was a troubleshooting step in another area). The water not dispensing was due to the line being frozen! Putting all items in a cooler with a couple blocks of ice and leaving the freezer door open for the length of watching a movie, the water was flowing again. Still no ice though. Ice maker vs mother board at the rear of the fridge, Hmmmm. Went with the ice maker, watched video, ole Steve makes the plugs disconnecting look easy, I had to use a flat head screwdriver to open the clips (he doesn't mention that) and I had 4 screws where he had 3. Also he didn't mention about the instructions which gives you 3 options with your unit. I had to re-use my Plastic Stripper Plate along with the Fill Cup and Ice Maker Insert. After completion of installation and about a half hour later, I heard ice fall, Wooohoooo!!! Overall the experience will make me think to utilize PartSelect again when needed. Reasonable prices and decent shipping time. Now the freezer light is out...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from Broomfield, CO
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice make stopped making ice
Went to GE website and researched the problem for the model, determined that it was 90% sure it was the Ice maker, I ordered it and it arrived the next day, installed it and it began working immediately,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Conti USA, Inc. from Fort Lauderdale, FL
- Parts Used:
- WR30X10093
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
change of ice maker
It was exactly as shown in your instruction video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from Abilene, TX
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
ice maker was leaking water. Cubes were sticking inside tray.
Reviewed video which was very helpful. Loosened two philips head screws, lifted up ice maker, unpluged power suppy and reinstalled. One of the easiest replacements ever!!
Was this instruction helpful to you?
Thank you for voting!