MCG23MISAFBB General Electric Refrigerator - Instructions

Read your instructions, which were very helpful, and followed them to install. It took a while for me to realize that the threaded cap at the end of the auger was a left-hand thread. Other than that, I had no problems.

Two tabs hold the switch in place. I used a plastic wedge to remove the switch. Removed and replaced the two connectors held in by friction. Painless.

shut off water supply to unit, pull the unit out,unplug, unscrew lower back cover, locate valve relay unit (bottom left, black and clear hose coming out of it) undo the quick connect for the clear water hose on the right (black one is for ice).

front of the unit, bottom left, locate the other hose (longer one) running to the freezer door from under the unit, undo quick connect.

Inside unit, remove middle drawers, careful with the glass panels as these just lay on top and are not fixed.

undo the 3 screws for the old tank, pull it out, snake the hoses thru the grommet on the bottom, reverse process...all set!

Just pop the old one out, careful not to lose the wiring inside the ref wall & popped the new one in.

Part arrived very fast as ordered..need to pry old switch out from top..use care to push the retainer down..after old switch was 1/2 out, I used a putty knife for better leveridge.Remove wire connector...after plugging in the wire connector to the replacement switch, make sure the switch is properly positioned so the switch will depress when door shuts.

look very carefully at the picture you provided in the parts fish, removed the ice maker tray and the rest was very easy ,i saved alot of money and time doing it myself.

My GE refrigerator emitted high pitch noise a short while ago. I tried different dampening methods that helped but not eliminating the problem. I finally replaced the fan, motor, and associated parts and solved the problem. The total cost was about $50.

Replaced flapper

This repair was very simple to do. I cannot say enough about part select dot com. I feel that I am a definite handy man yet the videos on the part select dot com site proved to be valuable. This video showed and reminded me that the plastic bushing holding the auger on was reverse threaded. Being a rightee tightee leftee loossee person embedded in my head I would have worn out that bushing holding the auger in place. I recommend not only purchasing from partselect.com YET please watch the video on this site prior to this installation. This made the installation not only simple yet informative. Thanks!

i used the video it showed on the site or iwould not have been able to do it

Thanks to others who also gave some detailed instruction on repairs I was able to do the same. I have a GE Profile side by side refrigerator/freezer Model No. PSC25PSSCSS The first repair I did was to remove/replace freezer defrost thermostat sensor that is cliped to condenser tube I snipped the wires close to the thermostat and pulled it off the tube I stripped the ends of the wires and twisted the strands then placed a piece of heat shrink tube onto the wire pushing it away from the exposed wire then I soldered the two color coded wires together then I pulled the heat shrink over the conection and used a lighter to heat up the heat shrink until it sealed the conection repeating this on the othr wire as well. I then removed the Old defrost Heater element by removing to screws then I disconected the two wires by simply pulling the connector plugs off both ends of the heater element assembly. This fixed the freezer being too warm for a short time but it started getting warm again that's when I noticed the defrost fan was not working, when you have the door open to freezer push the door switch in you should hear the fan come to life and blow hard. The fan was replaced I had to remove everything to get to it it's pretty simple to do it just unplugs make sure you order the right fan though My fan comes with the Thermistor already integrated into the plug this makes it easier. This fixed the problem with both Freezer & Refrigerator The Temperatures returned to normal Freezer 0 degrees Refrigerator 37 degrees I also checked out the refrigerator side Condenser I noticed only that the Condensate pan was starting to rust so I will remove it and use some Muretic acid to clean it up and then spray it with some Cold Gavanize with Zinc you can get this spray paint at Home Depot it seals and prevents rust. Or you can order a new one for about $ 16 bucks but it will start rusting just like the old one did eventually if you do order a new Condensate Pan I suggest spraying it before you reinstall it so that it will not rust. Greg H. Eldorado, AR

Remove lower front panel, disconnect damaged union from water hose under freezer door, replace with new union, tighten and reattach front panel. No more water coming from under the unit. Ice maker and dispenser features returned to working order!

I replaced that part, but I still have the same problem, no water is dispensed. I believe I may need a circuit board. The problem was not the parts I replaced.

I am 85 years old and had no trouble replacing the Augar. Removed ice maker from frig. Remover the ice shield (one screw, remove front panel (2 screws) carefully removed augar assy.

Removed the lock washer,the the end plastic nut, being careful in removing the ice crusher blades. Replaced the augar and all parts. Checked out the ice dispenser and the crusher, both worked fine

Ice maker assembly removed from refrigerator and disassembled. Note nylon nut holding the Augur in place is removed clockwise. As you take the assembly apart, note each piece for reassembly.