GTS18KHPARCC General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Hillary from MONTCLAIR, NJ
- Parts Used:
- WR02X11330
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Leaking from connector every time water was used
I watched the instructional video on this website and did everything that it said. There is no more leak when I use the in door water. Was as easy as it looks in the video and I am very happy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tina from Beaumont, CA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker was not making ice.
First i removed two screws that holds the ice maker in, unplug the plug to the ice maker. I was able to remove the old one. Place the new one in screwed in the two screws and pluged in the plug and in just a little while i had ice again. I am a women, if i can do it any one can. I had a repair man tell me it was going to be $250.00 dollars to replace it. I got on line ordered the ice maker and had it in 4 days. Very fast shipping and easy to install. Tina Kearns Beaumont, Calif
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Mahomet, IL
- Parts Used:
- WR30X10093
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
The ice maker needed replacing for a couple of years. Then, a couple of weeks ago, the water supply stopped serving both the ice maker, and the drink dispenser.
I ordered both a new replacement ice maker, and a new solenoid/pump. They were delivered to my house within one day and I had them installed in a matter of an hour. I had to use the power extension cord supplied with the ice maker.
The new "quick connect" hose couplings on the new pump are great.
The new "quick connect" hose couplings on the new pump are great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Tulare, CA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
No ice in hopper
Ice hopper had no ice in it. But water in door worked and if I added ice to hopper, it would dispense in door. I added water to ice maker but no ice was made. Replaced ice maker and all it required was to unplug harness and remove two screws with nut driver. Easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William E. from Centennial, CO
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Old ice-maker went SOUTH
If a 74 year old guy can install an ice-maker in a 20 + year old fridge in 20, or so, minutes it must have had good pictures and BIG PRINT. Working quite well at this time!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Ulysses, KS
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old Ice quit working, would make ice but wouldn't flip ice.
Removed old Ice maker and replaced with new Ice maker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from new city, NY
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
ICE MAKER gave out after 20 years
TURN WATER OFF TO REFRIDGE. TURN OFF ELECTRICITY.
Remove old ice maker (AFTER REMOVING THE BIG ICE TRAY) by disengaging two philips head screws but don't totally unscrew them. You must then totaly unscrew the bottom screw below the top two screws. Unplug the 5 head connection. (electricity)
Use adapter for the electrcity, etc from the box, (five head connection) Use the old plastic hose to hit the new cup. TIGHTEN TOP SREWS. LEVEL BY EYE. Turn the system on. Prime with some fresh water.
PS make sure that the light is on (green) and you will be in ice city. Be careful not to disengage the elcectic head when replacing the big ice tray.
HAVE A COCKTAIL!
Remove old ice maker (AFTER REMOVING THE BIG ICE TRAY) by disengaging two philips head screws but don't totally unscrew them. You must then totaly unscrew the bottom screw below the top two screws. Unplug the 5 head connection. (electricity)
Use adapter for the electrcity, etc from the box, (five head connection) Use the old plastic hose to hit the new cup. TIGHTEN TOP SREWS. LEVEL BY EYE. Turn the system on. Prime with some fresh water.
PS make sure that the light is on (green) and you will be in ice city. Be careful not to disengage the elcectic head when replacing the big ice tray.
HAVE A COCKTAIL!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Eugene, OR
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The door activated light switch was missing.
Pulled the two wires out from the access hole in the lower part of the refrigerator. Put them in the spade connectors on the new switch, and pushed the switch into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Medway, MA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
ice maker not calling for water to make ice.
I removed the screws that held the unit in place, and also the screws that held a plate that covered where the unit plugs in. I unplugged the unit, and removed it. Put the new one in, reversing the steps. Turned the new unit on, and had ice in 45 minutes! Summer is coming, I need my ice maker! This is the second unit I have replaced on this refrigerator, the first one was not releasing the cubes. This second one was a different style than the first, but same install process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from Elkton, MD
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice Maker Leaked Water
Removed Ice Maker (2-Bolts)
Removed Ice Tray Screw Motor (to get to Ice Maker Plug- 4 small screws)
Installed new Ice Maker and reinstalled Ice Maker Screw Motor
Extreamly easy
Removed Ice Tray Screw Motor (to get to Ice Maker Plug- 4 small screws)
Installed new Ice Maker and reinstalled Ice Maker Screw Motor
Extreamly easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Brooklyn, NY
- Parts Used:
- WR30X10093
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
My Icemaker arm was broken. It didnt move up or down by itself.
I removed the ice tub. Removed the screw on the left side that holds closed the section where the icemaker plug is connected. Disconnected the plug. Then removed the bottom right screw. I was then able to remove the Icemaker by unhooking it from the bcak freeze wall. I disconnected the icemaker from the fan gaurd. Removed the icemaker cover. unscrewed the 3 icemaker screws and opened up the chamber. removed the old Ejector Blade Drive Cam by removing the outer srew that hold the gear to the icemaker. changed the cam with the new one and reassembled everything.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Darien, CT
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker stopped working; would not fill
It was as easy as the instructions were clear (and they were). Remove 2 screws and two nuts, pop out the old ice maker, pop in the new, plug in and tighten screws/bolts. It worked. I'm happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Mattoon, IL
- Parts Used:
- WR30X10093
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Icemaker quit making ice.
The parts were here the next day. After removing the old ice maker it was a simple installation using the adapter cord furnished. It took about 15 minutes. You have to work with the cord some to get it to fit behind the ice maker, but it does fit. The ice maker started up immediately & works great.
Was this instruction helpful to you?
Thank you for voting!