PSB48LGRAWV General Electric Refrigerator - Instructions

Unplugged fridge, and turned off water supply. Removed cover from back of fridge, followed the plastic tube down to water valve.
I unbolted the mount holding water valve in place, removed the input tubing on top by unscrewing nut. I made a note of which outbound plastic tubing went to water dispenser, and which one went to icemaker, and which side of the water valve they plugged into, and then cut the tubing very close to the old valve.
I slid the tubing into the new water valve, and I felt it lock into place, very easy. Attached the input water line and tightened the nut.
Reattached the water valve mount to the body of the fridge, replaced cover, turned water valve back on and checked for leaks (there were none).
Plugged in fridge, tested dispenser, everything worked just fine. No leaks.

1. Turned off water near hot water tank 2. Removed back (small section) of the refrigerator, only 7-8 screws. 3. Disconnected the old water hose (comes out easily. 4. Reconnected new water valve 5. Turned on water @ hot water tank 6. Replaced back of refrigerator. All done! I have never done anything like this, and I had no instructions, very easy to figure out. The part cost $48 here.

simply read the instructions

I watched the video, and noticed that they did not even turn off the water. The replacement took less than 30 seconds once the filter was filled with water.

it was easy. Open the fridge,untwist the old filter. Open the new filter, fill with tap water and twist in place. Run water through it for a few minutes to insure it is working and filters the water.

Poped whole switch out with flat head screw driver. Removed wires with needle nose players and held the wires so they wouldn't get pulled back inside fridge shell. Attached wires to new part like a plug. Lights ccame back put new switch back inside wall. Shut door

Followed the instructions from your site and they were perfect. Unfortunatly that wasn't the problem. It still doesn't work.

turn water off to ice maker,unplugged refrigerator, took back panel off took old part off and put new part on

After gaining access to the back of the refrigerator. I shut off the water valve and pulled the electrical power plug. I removed 6 screws from the access panel. I then removed 1 screw holding the water valve. I disconnected the electrical connectors. Disconnected the water inlet tubing with an adjustable wrench. I removed the water to the door and water to the ice maker by pushing in on the collar which released the tubing. I discarded the old valve and installed it in reverse order. Did not fix the problem. My next guess is the control module.

replaced double outlet water valve. Valve works as it should. Shipping was much quicker than I expected.

watched your video,went to work

pullee refrigerator out to get to back un pluged power took off back cover unscrewed one screw to loosen water valve unscrew water inlet line ther are two water lines in back of water valve i cut them as close to water valve as i could push the water lines that i cut off into water valve makin sure in the rigfht place they are quick disquinect just push in and ther on screwed water valve back on connected water inlet line replaced back cover pluged in power pushed refrigerator back in and was done it had to run for a little while to get the air out then worked fine

Unscrew the mounting screw and cut the tubes as close as you can to the valve. You cannot reuse the valve as the self sealing lock washers will be destroyed once you take out the tubes. Push the newly cut tubes into the new self sealing new valves and remount. Easy Peasy!

Unplugged fridge, shut off water supply. Removed bottom back panel of the fridge and carefully vacuumed up all the dust. Located the water valve to the left of the compressor. It is attached to the side of the fridge by a metal bracket. Remove the screw from bracket and lift up on the whole assembly. Now I removed the electrical connectors and pushed in on the quick release tabs to pull out water lines. When installing water lines to new valve be sure to push them all the way in. The water lines are marked so you will know how far they must go in. Attached electrical connectors and remounted whole assembly back to the side of the refrigerator. Turned on water supply and plugged fridge back in. Checked water dispenser for proper operation and also checked water valve for leaks. Reattached the back cover to the fridge and that was it.

1)turn off water supply to appliance 2)disconnect appliance from power supply. 3)remove grill. 4)remove valve retaining fastener. 5)disconnect two wiring devices. 6) depress retaining devise at each water line to disconnect. note: if the lines do not releace, use utility knife to cut lines as close to unit as possible. 7)attach new valve in reverse order.