GSG20IBPCFWW General Electric Refrigerator - Instructions

replace sensor in refriger.

We used partselect troubleshooting appilication to figure out what was most likely causing the problem and what part would fix it. The suggested part was the freezer's defrost thermostat and the probability that this would fix it was 52%! The diagnosis made sense because when we emptied the freezer to see the part, the coils were frozen solid with a thick layer of ice. We thawed the ice and the refrigerator worked fine for a day and a half at which point the ice was back and the refrigerator was warm again. We ordered the part. It came in 2 days. We snipped two wires and removed the old part, twisted the wires of the new one in place, taped it up and it worked! Fast, easy, cheep! $8 For the part, about the same for shipping and no $70 service call. Selectparts is bookmarked for "house repair"!

Remove the shelves then remove the back by removing the two screws at the top of the panel. Locate the temperature sensor on top of the coil. Cut the wires and replace with the new one. Use wire nuts and electrical tape to reconnect the wires.

Replaced top sensor in ref. and top sensor in freezer as well as defrost thermostat - works as advertised - easy fix, saved a bundle thanks to this site! Parts ordered and shipped quickly and without complications!

I replace defroste thermostat :i defrost al the ice

the parts I ordered did not fix the problem the problem was with repairman did not follow the instruction and cut jumper wire on main control board

I had already replaced the icemaker and solenoid valve and had not solved my problem. After I looked at the back wall gasket, it was obvious that the element was getting too hot. Installation was really simple- unplug refrigerator cord, remove frozen food and racks, remove light cover and back sheet metal by removing 4 screws, cut and splice wires to new parts. Reinstall.

Open up the freezer make shore the fan is running/unplug the unit take out the Shelf,s take a 1/4 inch nut driver and take the back panel out pull out the ice box pull up on the back panel and pull it out to expose the coil it should be blocked with ice if it is take a blow dryer and defrost it unplug the fan and push it up. On top of the coil you will fiend the defrost timer take your hand and unstrap it and pull it out. Cut the wires and strip the wires back enough take the new part and wire nut the wires together and tape with electrical tape and put back on the coil. Put every thing back together your dun plug the unit in and wait over night if you can to let every thing cool.

1.- ordered the thermostat replacement.2.- unplugged unit 3.- empty unit, removed racks too(freezer only) 4.- used a hot hair dryer to melt the ice,kept drying water inside the unit. 5.-used electrical pliers carefully removed damage thermostat.6.- putted on new thermostat, used standard wire connectors to keep wires together and wrapped them with black electrical tape. 7.-gentle replaced thermostat back in contact with the other pieces.8.- returned back racks and all removed pieces,drying all water from melted ice.9.- plugged it,...done

watch you tube demo how to do it.

followed part select video instructions

Replace defrost termostat and temperature sensor

Followed the repair video, was spot on!!

luckly i have a bit of experience in refrigeration im an hvac technician by trade. this repair was a bit tricky in that i did not know at first if it was a Temperature Sensor issue or the main control board. I had tested the defrost termination thermostat and the defrost heater and as i suspected they were ok. Next i wanted to test the thermistors (temp sensors) it is hard to find technical data on these fridges. I needed to test the thermistors resistance @ a certian temperature to ensure they were working properly but where do u get such data? I also wanted to know some information about the logic programmed into the board (i.e when do you initiate defrost etc. . .). I had no such luck so i figured since i tested the defrost heater and thermostat and they were ok and all of the evap fans and such were working i'd order a circuit board and new thermistors. Got the CORRECT PARTS from this site in 2 business days and my fridge is working great! changing the parts was really easy, figuring out which parts to change was the only difficult thing about this job.

Little difficult getting the switch out, had to pry wth some force. New installation was real easy.