GTS18KCMCRBB General Electric Refrigerator - Instructions

I'm not a DIY-er, and wasn't sure a 20 year old refrigerator was worth the repair, but for $30 I could afford to be wrong. The swap is pretty intuitive, especially in my case since the problem was that the water tube from the valve to the ice maker had detached from the coupling. So I didn't have to cut anything off, just inserted the tube into the new valve. Reconnected the supply line, screwed the assembly back on the refer, and Bob's your uncle. Other than unloading some canned goods to lighten the refer, longest process was finding the right size nut driver in my disorganized tool tray. Be aware, there are NO instructions included with the part. Found a good video on you tube that confirmed the obvious. Glad I took a shot!

replaced lights in refrigirator and freezer

I pulled off the plastic strip that says “ vegetables” on one side “fruit” on the other. That exposed screws on the left and right sides. I unscrewed both sides I did the same to the back support arm put the new arm in and it works great! The man who helped me at part select was so patient and so kind and helping me select the right piece to begin with to make sure I had the right model number. Could’ve had a better experience with the repair company. Tammy Peterson

Did the repair just as the instruction said, once I read it. The part I didn't read was that if the plug was under the ice maker, you had to take the wire out of the clip on the side. So, had to dismount ice maker, unclip wire, remount maker, plug it in. Still under 30 minutes. Thank you.

Pulled the fridge from the wall. Then shut the water line to the fridge off. Pulled the water line to the ice maker out the old grommet. Then a screw or two from the cover over the bottom back of the fridge, so I could get to the outlet valve kit. Only 1 screw was holding that. Then took the lines off the old outlet valve. Took the little hose off the grommet on the inside of the freezer that leads the water into the drip pan to the cube tray of the ice maker. Then grabbed pliers for the grommet on the top back of the fridge. And pulled and twisted alittle till it came out. It was alittle hard but got it out. Cleaned the out sticky tape off around the hole where the grommet connects. Hook the water like that goes to the grommet for the ice maker to the new grommet. Peeled the paper of the sticky tape for the new grommet. And placed it in. Then connected the rest of my water lines to the inlet valve. Put everything back the way it was. Then plugged and turned the water back on. And in 2hrs or so I had ice fall in the tray and continues to make ice no problems. “Note also I didn’t actually unplug my fridge I did it all why it was plugged. Thought it would be best to let you know. LoL but a small socket 1/4 with a 1/4 drive or worked. Also I think my grommet was harder to get out cuz it was froze due to the water leaking in the grommet.

Remove ice maker out of fridge; remove 3 screws
replace defective part re-install all components 30 minutes later " magic ice again. Very easy repair most important low cost. Thanks "Parts Select"

Unplug refrigerator and turn water supply off to the ice maker. Remove the screws holding the bottom cardboard-like cover from the lower back of the refrigerator. Remove the water supply line to the old solenoid with 1/2 inch wrench. Unplug the two power supply wires to the old solenoid. Remove the screw that holds the solenoid to the back panel of the unit. After the solenoid is pulled out, remove the output hose with a 1/2 inch wrench. The configuration of the replacement solenoid is likely a little different than the original, but it seems to be rather universal and will fit back into place and perform properly. The new solenoid does not use a compression type nut to secure the output line. It's just a simple push-in connection. The wires may have to be rerouted a little, just keep them clear of the evaporator fan blades Reverse the removal procedure and you're done.

First removed the two screws that holds the old ice maker in place. Unplugged it. The freezer compartment was too narrow to allow the unit to slide out or turn in any other direction. Had to also remove the two front screws from the left side ice bin track and swing it down. The door opening was also too tight. Scratched the plastic door jamb putting the new unit in but other than that all is well and functioning well.

Other than having to bend the bracket 90 degrees it was an easy install.

After determining that the ice maker on this relatively new refrigerator would make ice cubes if it received the proper amount of water. Ordered the valve and received in a couple days. Using a nut driver, removed the cardboard cover from the back of the refrigerator. Removed one screw holding the valve bracket to the fridge and removed another screw holding the water supply line and the water line to the ice maker in place. Pulled plug on fridge and removed 2 wires from valve. Removed inlet and outlet lines from old valve and reversed the process installing the new valve.

First I removed the ice tray rack lifting it out of the way to reach the back cover of the fan. Then, the whole back inside panel had to be removed. Two screws removed the fan and bracket from the freezer unit. The missing bumper lid just snapped into place. Replaced everything in reverse order. Pretty easy job.

Tried replacing water valve since no water in ice cube tray. Exact part not available due to age of refrigerator, but I got the equivalent replacement part for $18. Mounting holes different, but I made it work. Also one connect on new one slip connect whereas both compression fittings on old valve. I put it back together and icemaker now works great.

i took the backing off with a screwdriver, cut the wires and put the 2 wires on that came with the thermostat. p.s. make sure you pull the power plug before you start.

I had made a dry run at the repair after watching the instructional film provided by part select and it seemed easy enough.
The only problem was that i needed to use the electrical cord extender (provided) to adapt to my plug type. That presented a problm because it needed to be tucked up out of the way to allow the ice bin to clear. Just needed to be creative in how you wrapped the cord behind the ice maker unit before snugging the attachment screws.
Cranking out ice like crazy.

Three easy steps, take off old part then all you do is tighten nut on one end of part and then just push other end of pipe down in slot. Did half to remove nut off the top end of tube very simple to do