PSB48LGRABV General Electric Refrigerator - Instructions

Rolled the fridge away from the wall, unplugged the unit from the wall outlet, and removed the back panel by taking out the 6 1/4" nuts that held it in place. Vacuumed the dirt and dust out, and sneezed viscously for 2 minutes. Removed the 3/16th nut holding the water relay. removed the inlet water line, and quickly replaced it. dried off, then went down stairs and turned off the saddle valve. mopped up the water, then removed the water inlet valve. Removed the 2 water lines to the unit (Ice and water feeds) and removed the 2 wire connectors. reversed the process in installation, except the drying myself off part, and sneezing from the dust and dirt.

Really easy

Replacing the water valve was easy - the video was excellent. However, the problem was not solved - no water even after replacing the water valve. Anyone have any other thoughts?

It went exactly like the repair video showed. I removed the back cover, unhooked the water lines, unplugged the electric connections, and replaced the valve. That video made it super easy and it is now working like it should.

Just turn the cartilage out and put the new one. Very simple

Replaced Water Filter (twist off old filter; twist on new.)

1. Turned off water near hot water tank 2. Removed back (small section) of the refrigerator, only 7-8 screws. 3. Disconnected the old water hose (comes out easily. 4. Reconnected new water valve 5. Turned on water @ hot water tank 6. Replaced back of refrigerator. All done! I have never done anything like this, and I had no instructions, very easy to figure out. The part cost $48 here.

Removed back panel. Cut the water lines and replaced the double outlet water valve. The only issue was the long period of time until the water flowed from the outlet. Be prepared to wait, it will take some time for the water to flow.

Simple repair. I first shut off the water supply to the unit. I then removed back cover from lower part of the unit. The water valve is on the lower left side. I began by removing the screw on the bracket that holds the part in place. This screws into the back of the unit. I then disconnect the water line by unscrewing the fitting. Then unplugged the two electrical connections in the back of the unit. Lastly, remove the two hoses that plug into the bottom of the the unit. The installation was essentially the reverse of the the removal. The whole process took about ten minutes.

with my hands

This repair is EXTREMELY easy to conduct even for the novice. The first step was to shut off the water supply at the wall, and disconnect the power cord to the refrigerator. Remove the six panel screws to remove the lower back panel. On the lower left hand side is the water valve. This is connected by only one screw, so that was removed. Compare your new valve with the one you are removing to double check that the units are the same. Disconnect the inlet water supply line and connect it to the new unit. Disconnect the two water outlet lines from the old unit and connect to the new unit. Finally, disconnect the two power plugs from the old unit and connect to the new unit. These are all colored coded or different sizes, so there is no way to fowl this up! I just recommend disconnecting and reattaching one at a time so that you are doubly assured you are doing this correct. Reattach the valve unit back onto the side of the refrigerator. At this point, I turned on the power and water supply to check for leaks. Also, have someone run the water in the ront panel dispenser to ensure things are working properly. Once that is completed, reinstall the back panel and you are done. I did this project about two weeks ago, and things are working great now. Saved a lot of time and money by doing this job myself.

it was easy. Open the fridge,untwist the old filter. Open the new filter, fill with tap water and twist in place. Run water through it for a few minutes to insure it is working and filters the water.

After confirming that a frozen water line was not my issue, I confidently bought this item and installed it within minutes after receiving it! It is easy to install - just close the connection to your refrigerator, open the rear lower panel, disconnect the water tubings and electrical connectors. Reverse that - you have the installation. Plug the refrigerator back on, turn the water back on for the refrigerator - and observe for any leaks. If no leaks - try dispensing water. Working great for me! My refrigerator's model is a GE, model # zfsb26dnass.

Followed the instructions from your site and they were perfect. Unfortunatly that wasn't the problem. It still doesn't work.

I watched the video instruction and it was very easy to replace. took me less than 30 minutes.