PTG22LBSARWW General Electric Refrigerator - Instructions

I followed your video and completely dismantled the refrigerator evaporator motor, fan, brackets, and grommet, I completely cleaned the refrigerator including the cooling coils. I then ordered the evaporator motor ,fan, grommets, lid bumper, and brackets. The order would take a week to arrive. In the meantime I cleaned and reassembled all the old parts, waiting for the new ones to come. Guess what! The refrigerator was quiet as a mouse. I really did not need the new parts, but I kept them anyway just for good luck. Not bad for a refrigerator that's twenty four years old.

Bent the motor bracket down, then using a rat tail file, elongated the holes in the back panel of the refrigerator to secure the fan in the "centered" position. This was a problem that was with the refrig. since it was made. The parts involved were perfect. NO problem at all installing them.

I have not yet done the repair. After watching this repair video two problems came to mind. First I only ordered one grommet not knowing that there were two (or more I don't yet know). The second problem is that this video must be for a fridge from like the 1940, but it looks NOTHING like mine from 2008. The manual shows a bazillion parts and frankly I'm just a wee bit afraid to get started, and I am generally very handy, buuuttttttttt I don't know about this one

Gaskets designed to just press a flange into channel around doors. I tried everything..I pre-heated gaskets ; I put dish soap around flange; I used (carefully) a heat gun as I pressed gasket in. Really very difficult to get the gasket to seat fully. I don't know if there is a tool to help you do this, but you need strong fingers/thumbs and endurance. Once seated, you will need to heat the gasket to get it to fully seal against the fridge. Just lightly heat along the gasket with the doors closed and press open the fold with your fingers. I let the doors stay closed over night. Works great now, but I probably will call a repairman the next time. I miss the old gaskets with a zillion screws..PITA, but easier.

Totally followed the instructions of the video that came with the sensor. Unplugged the the fridge, defrosted the freezer. Cut off the main sensor that usually is the one that goes out. Installed the the new sensor with new wire terminals, crimped them and covered with electrical tape. Fridge works like a charm. Partsselect is excellent. Saved me a few hundred dollars versus having a GE Tech come and do it.

took a little more effort than the video show to remove old module and replace new. Works fine now.

It was way to ez to install only a couple of minutes that's it

Pulled the two wires out from the access hole in the lower part of the refrigerator. Put them in the spade connectors on the new switch, and pushed the switch into place.

Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of your company & it's repair video. THANK YOU SO MUCH

Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks

Once the part was received, it was very easy to snap the new part into place, and reinstall the drawers. No tools were required to complete the repair.

removed the inside fridge electrical panel and swapped switches

easy pry out, disconnect wiring, connect on new switch and press in switch.

It was very tricky getting the old piece out, even though it was partially broken... I ended up snapping the old piece to remove it. Trying to install the new track with the glass shelf above was not working at all, but once I removed the glass shelf above it, the new piece went in pretty easily. With the glass shelf out, I could angle the track upward to get it into position. In retrospect, I should have removed the glass shelf from the start... it would have made removal of the old piece much easier.

We just pried off the fan blades and pushed on the new part. Could not have been easier. The rat has been permanently dipatched and, hopefully, that is that.