PSF26RGWCWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- George from ARLINGTON, VA
- Parts Used:
- WR02X12274, WR01X10210
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Stripped Front Leveling Roller & Screw
Raised side of fridge enough to get 1/4" ratchet with 1/4" socket under roller wheel assy. Removed three hex-head screws to separate damaged wheel assy from fridge frame. From panel below fridge compartment, backed-out stripped leveling screw. Mounted new roller assy and then threaded in new leveling screw from front. Lowered fridge and adjusted leveling screw for proper height. Suggest putting a 2x4 under fridge for safety when hands are under unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roberta from Estero, FL
- Parts Used:
- WR71X10582, WR02X10662
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original shelf was a split/slide in shelf which I did not like
I removed the old shelf and installed the new one!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from pasadena, CA
- Parts Used:
- WR32X10156
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The glass was broken in a move
The new shelf went in really easy. It just fit in the alloted slot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curtis from Corona, CA
- Parts Used:
- WR17X11459
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Ice maker would not dispense ice, crushed or whole.
Removed the ice maker from the freezer. Unscrewed the outer cover/base of the ice maker. Unscrewed the long lever that opens the ice chute. This freed up the feeder coil enough to pull it out enough to replace the cup drive. Once I replaced the cup drive, I laid it back down into the ice maker bin, reattached all the screws and it worked! The old cup drive had a tine broken off which would not allow the feeder coil to turn. It seems like a weak part and I anticipate I may have to replace it again in a few years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RICHARD from SPRING HILL, FL
- Parts Used:
- WR17X11505
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice Would Not Come Out
Removed tray, threw out ice , removed 3 screws used 2 screw drivers to seperate part & re installed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Milford, CT
- Parts Used:
- WR23X21444
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Freezer Light switch broke
Your instructions were "spot on"! Pried out broken switch with screwdriver-reinstalled new switch. Very easy! Ordered on line on a Wednesday new part arrived on following Saturday-Great service and will definately use again. Highly recommend PartSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Weeki Wachee, FL
- Parts Used:
- WR17X11447
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Ice Auger Broken Twice
This is second ice bucket auger I had to replace, don't know why it's breaking , but partselect was great to work with, replaced the broken part, was fast and very nice to help. I really appreciated their service. There was no repair, I mean, open the box, take out broken auger box, put in new one. No possibility of error.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from MARTINSBURG, WV
- Parts Used:
- WR57X10070
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
No water from the dispenser and Water leaking on floor
I searched YouTube for the problem and was quickly taken to several videos that detailed to required actions. This encouraged me to proceed, so I took the back cover off and found the water valve leaking. I then googled the make and model of the frig and found the part. The YouTube videos provided all of the details needed to determine the problem and replace the faulty part. Once the part arrived, I was able to install the new one in a few minutes. Operation returned to the water dispenser and the leak was gone. Total cost of the repair was $56 and took about 1.5 hours to remove the original part, order the replacement and install it when it came. Perfect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jared from TAYLORSVILLE, MS
- Parts Used:
- WR72X10247
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice machine quit working. Motor fell out!
1-Remove the ice bucket. 2-Nut driver 1/4 inch to remove three screws in bracket. 3-8mm nut driver to remove one screw in motor mount (where broken). Install new part. Reverse order to complete repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Peoria, AZ
- Parts Used:
- WR72X10248, WR72X10247, WR17X11459, WR17X11458
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Stripped out helix lock, broken bucket glide rails
PITA to take apart, finally had to use two screwdrivers to pry up on the mechanism that turns the auger in order to gain access. Once I figured that out, the rest of the repair was a breeze.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from ORANGE, CA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Unit had stopped making ice
Ordered the icemaker replacement. unplugged the unit, followed the simple instructions and got it done in less than 30 minutes. It did take a LONG time to start making ice. But it's working now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Naples, FL
- Parts Used:
- WR17X11459
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice Dispensing Cup broke in half
I removed the ice from the tray, took out the four screws from the tray, pulled up the metal spiral took out the old drive cup, replaced with the new one, replaced the screws and put the tray back in the freezer. A piece of cake. Thanks for your prompt service and the reviews on how to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rachel from LUDOWICI, GA
- Parts Used:
- WR50X10068, WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Would not defrost
Replaced defrost thermostat along with temp sensor watched the video on this page simple fix
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from ZIONSVILLE, PA
- Parts Used:
- WR17X11168
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
water line (from the PS304374 Dual Inlet Water Valve) to the ice maker was craked and leaking
1. Removed the back panel of the fridge to get access to the inlet water valve.
2. Removed black poly water line from valve (pull back on white ring where line is attached and pull the line out)
3. Removed the inlet tube from top-back of fridge (where it goes into the ice make). use putty knife to get under the sticky white gasket beneath the black oval housing and pull the tube out form the back of the fridge.
4. Replace the water line with new part taking care to properly seat the line into the the bottom water valve and pushing the water tube into the hole for the ice maker.
Note: Be sure to take off the protective covering from the white - sticky grommet and push to adhere to metal on fridge.
to be safe - use a bit of clear silicone chaulking round the perimeter of the grommet and push to tighly bond the water inlet tube to the fridge.
The reason for this - is that if you do not get a good bond using the white - sticky gormmet alone - you may have the water tube inside the ice maker freeze up.
Also once the new water line is installed be sure to secure the line to the metal back of the fridge - so the line will not move. some fridges come with metal hose clamps to do this - otherwise use duct tape
2. Removed black poly water line from valve (pull back on white ring where line is attached and pull the line out)
3. Removed the inlet tube from top-back of fridge (where it goes into the ice make). use putty knife to get under the sticky white gasket beneath the black oval housing and pull the tube out form the back of the fridge.
4. Replace the water line with new part taking care to properly seat the line into the the bottom water valve and pushing the water tube into the hole for the ice maker.
Note: Be sure to take off the protective covering from the white - sticky grommet and push to adhere to metal on fridge.
to be safe - use a bit of clear silicone chaulking round the perimeter of the grommet and push to tighly bond the water inlet tube to the fridge.
The reason for this - is that if you do not get a good bond using the white - sticky gormmet alone - you may have the water tube inside the ice maker freeze up.
Also once the new water line is installed be sure to secure the line to the metal back of the fridge - so the line will not move. some fridges come with metal hose clamps to do this - otherwise use duct tape
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Mahopac, NY
- Parts Used:
- WR62X10055
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker solenoid failure
several times I had to remove the ice maker door solenoid due to it sticking. I ordered a new one from parts select. Problem solved!!!
Was this instruction helpful to you?
Thank you for voting!