TFG27PRSCWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Harold E. from Hartselle, AL
- Parts Used:
- WR17X3095, WR17X10282
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
seal deteriotated preventing flappper from fulling closing, allowing escaping air to freeze up water line.
Snapped off the plastic plate covering the dispenser. Removed the four screws holding the mechanism in place. Remove the electrical connections. Pull the mechanism out and up carefully pulling the dispenser pad out with all the mechanism in place. Look at the mechanism before removing any parts to get a mental image so that reassembly will be easy. Remove any electrical switch or circuit boards and remove old parts before submerging the mechanism in hot soapy water for clean-up. The Clean-up will take longer than the disassemble and reassembling. After completion the dispenser works as it should.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynwood from Spring, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
flapper was curled at one edge allowing air to enter and causing frosting in the freezer
I followed a video supplied with the e-mail notification of the shipment of the part. This was one of the best experiences I have had with locating, purchasing and installing a replacement part for an appliance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from Paso Robles, CA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice Maker flapper
Your Video really made it easy, showing the actual replacment of the part. However I did have one problem, which was I could not unplug the panel just by pulling on the plugs. A locking catch is on each plug so I just moved the panel out of the way.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Raleigh, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice accumulation inside the ice dispenser.
I watched the Utube video, repeated the process at home while awaiting the part, and installed the flapper door in about 15 minutes after it arrived--piece of cake. The hardest part was removing the escutcheon plate on the front of the freezer door. I figured out I could slide a putty knife under it and the rest of the project was completed in no time at all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Charlotte, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Misting inside freezer which blocked the ice dispenser.
I followed the video instructions to the letter and it was very easy and a total success. I believe I would have had problems but for thr video demonstration which was very clear and straight forward in a simple manner. Thanks for the prompt delivery of the part and the help installing it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebecca from Banning, CA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
ice dispenser frosting up
Watched the video from your site and followed instructions, extremely easy after that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from Benton, AR
- Parts Used:
- WR17X11653, WR17X3489
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Flapper would not seal. Shield broken
Followed on line instructions. No problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald J from Seabrook, SC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Flapper door mis-shapened
Took the paper clip, pressed in through the holes on the bottom of the ice dispenser panel. Removed the four screws. Loosened the panel and removed the wires. replaced the flapper door. Then reversed the process. Your video was VERY helpful except for the paper clip. Had to get that off another web site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jon from social circle, GA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
frost formed because the ice damper let warm air into the freezer
Removed frame, unscrewed the electrical panel, and popped the flapper off. Installed new flapper. Replaced the electrical panel and re-installed the frame.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Ocean View, DE
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door flapper to ice needed to be changed
Repair went exactly like the video. With this video it was easy to make the repair. There were no surprises or problems and I felt confident in the videos instructions. It was like pushing the easy button.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DON from ZELLWOOD, FL
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice Shute Flapper Was Distorted And Did Not Seal Opening Causing Frost Build Up
Removed control panel by inserting small screwdriver in the 3 holes underneath to loosen. Remove 4 screws holding circuit board . Unplugged 3 connectors. Removing circuit board gave access to flapper. Removed flapper by unclipping. Installed new flapper and reversed disassembly procedure. This was 2nd time in 2 years I had to replace this part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Austin, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Heavy frost was forming where ice is dispensed
Watched the PartSelect video. Very simple and solved the problem. Very pleased with the repair and PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Houston, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice flapper replacement in freezer door
Looked at the instructional video and read previous customer comments. Didn't have to dissassemble rear of freezer door. Access through the front once trim ring and circuit board removed. Could not have done it with out the video/and or previous customer comments. Part was shipped and received immediately. Repairs complete! No more frost developing and plugging ice chute! I especially appreciate the customer comments on how to complete this repair!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from Cocoa Beach, FL
- Parts Used:
- WR17X4312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The silver plating on the auger was coming loose, rusting and getting in the ice cubes.
All I had to do was remove four (4) screws from the old ice bucket assembly to remove the front cover and attach it with the existing screws to the new ice bucket assembly. It was a very simple repair. Thanks for the expedient delivery and the exact replacement part that I needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leticia from El Paso, TX
- Parts Used:
- WR17X4312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The Ice Bucket had rusted
It was really simple, remove 4 screws form the old cover and put it on the new bucket. Simple, Simple!!
Was this instruction helpful to you?
Thank you for voting!