ZISS360NXCSS General Electric Refrigerator - Instructions

as per video

Removed the old filter. Filled the new one with water and put it in theplace of an old one. Flushed the system with 1 gallon of water.

Very simple, I followed instructions sent with the filter. Twisted old filter clockwise 1/4 turn to remove. Filled new filter with water, lined up arrow on filter to arrow on refrigerator, and then turned 1/4 turn counterclockwise. Filter raised and seated itself. Wiped few drops of water from refrigerator shelf.

Put spring on. Hardest part is the amount of space to work in. Clean under fridge first.

Folowed instructions

none required

Temp. Sensor was under an egg shaped cover on the left side wall in the refrigerator. Remove the cover, cut the two wires to the old sensor and remove it. Connect the new sensor to the two wires using butt connectors. Replace cover and done.

I have a GE Profile French door refrig. It's only about 4 yrs old and the defroster stopped working. I read the other repair stories and was able to narrow it down to either the temp sensor, defrost timer, or main board. The refrig section was up to about 47 degrees and freezer was around 25. I could tell it was trying to cool but couldn't. So I tried the temp sensor first. I cut and spliced the new sensor on the outlet of the Evap. Coil and it took about 15 mins. Turned refrig back on and waited. The coil started to ice over after about 5 hrs I left the back panel off so I could see if and when then heater kicked on. After about 8 hrs I looked in and saw a faint glow and water trickling down and running out the drain. Turned out the sensor was bad and wasn't telling the main board it needed to defrost. I would try the sensor if you are having the same issues before spending a lot of money on the main board, defrost heater and or timer.

My refrigerator was making a high pitched kind of howling noise. The PartSelect symptom that was closest was “unusual noise” and when I clicked that it said the evaporator fan motor fixes the symptom 32% of the time. Since my freezer fan speed sounded like it was constantly changing I went ahead and bought one which PartSelect delivered promptly. The installation video was great and although my freezer was not identical to the one in the video, the video was still very helpful. The only thing it didn’t say was how to tell if my freezer motor was the one with the thermistor although I suspect that they all are and that PartSelect is simply trying to save us money by showing us how to splice in a motor without a thermistor. Anyway, since I would have had to disassemble the freezer before buying the part to find out for sure, I just bought the one without the thermistor. This just meant I had to splice the new motor in, just like in the video. I think I would have preferred buying the motor with the thermistor even though it was more expensive. In the end my problem is solved so I’m happy. This is the third time that I’ve had to repair this GE refrigerator and PartSelect has been a valuable resource each time.

it was easy the only thing was i had to cut old harness to remove 2 wires that went to coil that had to go back in the new harness other then that a peice of cake.

i followed a video that was on your site, the video couldn't have been easier to follow it was step by step and very easy to follow, i replaced the evaporator fan motor and everything is working fine, i did notice that the evaporator coil was frozen pretty bad when i removed the back freezer panel i am going to check it again in a couple of weeks to make sure i don't have a defrosting problem as of now everything is fine i am hoping it was just the bad fan motor causing the coil to freeze up because of no air movement over the coil

luckly i have a bit of experience in refrigeration im an hvac technician by trade. this repair was a bit tricky in that i did not know at first if it was a Temperature Sensor issue or the main control board. I had tested the defrost termination thermostat and the defrost heater and as i suspected they were ok. Next i wanted to test the thermistors (temp sensors) it is hard to find technical data on these fridges. I needed to test the thermistors resistance @ a certian temperature to ensure they were working properly but where do u get such data? I also wanted to know some information about the logic programmed into the board (i.e when do you initiate defrost etc. . .). I had no such luck so i figured since i tested the defrost heater and thermostat and they were ok and all of the evap fans and such were working i'd order a circuit board and new thermistors. Got the CORRECT PARTS from this site in 2 business days and my fridge is working great! changing the parts was really easy, figuring out which parts to change was the only difficult thing about this job.

followed you online video and it was easy and simple repair only took about an hour frig is back quiet and working fine thanks also parts come fast

Followed the repair video, was spot on!!

follow repair viedo