ZISB420DXC General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Sandy Hook, CT
- Parts Used:
- WR62X10055
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice chute wouldn't open or shut correctly - rusted solenoid
Replaced rusted solenoid.
Popped front button panel off from the bottom using flat head screwdriver; Removed 4 screws holding electronics board and disconnected wires. Unscrewed 3 phillips head screws on old solenoid and replaced with new part. Reconnected wires to board, screwed back in, and pushed panel back into to place.
Thumbs up to PartSelect - fast, straightforward service and fast delivery.
Popped front button panel off from the bottom using flat head screwdriver; Removed 4 screws holding electronics board and disconnected wires. Unscrewed 3 phillips head screws on old solenoid and replaced with new part. Reconnected wires to board, screwed back in, and pushed panel back into to place.
Thumbs up to PartSelect - fast, straightforward service and fast delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from W Berlin, NJ
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice forming around shoot. Flapper door not shutting letting warm air in.
I followed they instructions from the other "do it your selfers" but only replaced the solenoid. This was the cause. Rust was keeping solenoid plunger from moving and this held the flapper door open. Very easy to repair!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from CAMARILLO, CA
- Parts Used:
- WR17X22070
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Leaking around filter bypass plug
Took old one out with my fingers. Put new one in with my fingers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from TYLER, TX
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Your video was wrong. Your step was to remove exterior frame on ice/water outlet. No need to remove.Wasted too much time trying to remove.
Remove control panel.
Remove four screw in control panel bracket.
Remove to bottom screws at bottom of solinid loose top screw.
Replace all screws.
Remove four screw in control panel bracket.
Remove to bottom screws at bottom of solinid loose top screw.
Replace all screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carla from RUSSELL, KS
- Parts Used:
- WR01X37886
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light bulb burnt out
replace a new blub
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dan from columbus, OH
- Parts Used:
- WR01X37886, MWFP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Water Filter and Light Dispenser replacement
My water filter was a breeze to install. Just push up and to the right and it locks right in.
As for the Water Dispenser light. Just screw it in!!
As for the Water Dispenser light. Just screw it in!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Resa from Potomac Falls, VA
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Flap on Ice Maker not closing
I searched the site, found the part - solenoid, watched the "how to" video and the repair was a snap. Saved myself tons of money versus having a repair person come over. I do have an older model and needed to prop the front cover panel off with a screwdriver (just under the covering) saw this on a posting from another individual, thanks for the heads up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Kingsport, TN
- Parts Used:
- MWFP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Scheduled replacement
Turned the old filter loose, removed the adapter from it, put the adapter on the new filter and turned the new filter back into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Secretary, MD
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice chute door not closing
I read instructions in all of the other repair stories everything went smooth no problems. Went and examined freezer door too see which type of door I had front or rear access. Popped off front LED panel, unpluged wires, removed 4 screws holding ice chute, removed 3 screws holding solenoid, slipped off solenoid pin, replaced all items in reverse order. This is one great site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rene from Lancaster, CA
- Parts Used:
- MWFP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Water flow from in-door dispenser was a trickle
We didn't think the dispenser problem was related to the filter - we were wrong! It took less than two minutes, including opening the box and unwrapping the filter. I'll definitely be changing my filter more often - and buying it through PartSelect. Your ordering was so easy and delivery was unbelievably fast!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wanda from FRANKLINTON, LA
- Parts Used:
- WR01X37886
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dispenser light bulb
Screwed bulb in and Light works!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Lake George, NY
- Parts Used:
- WR62X10055, WR17X10706, WR02X10585
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The ice dispenser door would not open or close.
It was actually very easy. You simply remove the display cover (you just want to be careful removing the display cover so as not to damage the lower part which secures it to the door), unplug the wires, remove the inner cover (4 screws) to gain access to the solenoid. Remove the 4 screws on the solenoid replace with the new one, put the inner cover back in with the 4 screws that were previously removed, plug the wires back in and then replace the display cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William c.. from Barberton, OH
- Parts Used:
- MWFP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
water leak
got new filter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from DYERSBURG, TN
- Parts Used:
- WR17X22070
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Slow water flow from water dispenser.
Took out the MFW filter.
Screwed in the MFW bypass.
Dispensed several gallons of water.
Saw good flow of water.
Removed MFW bypass.
Replaced MFW filter.
Our water flow was back to normal.
Screwed in the MFW bypass.
Dispensed several gallons of water.
Saw good flow of water.
Removed MFW bypass.
Replaced MFW filter.
Our water flow was back to normal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Shelby Twp., MI
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Flap to ice dispenser would not close
I followed the video provided, and followed the advice of bill from cleveland hts. ohio, and did not have to remove the trim to access everything. The video made it so simple, a monkey could have learned how in 5 minutes. Thank you very much for all the help on this website. I will recommend it to all.
Was this instruction helpful to you?
Thank you for voting!