ZIS420NXC General Electric Refrigerator - Instructions

Unplugged the refrigerator first....then on the inside of the fridge, I popped the temp sensor cover off (upper LH side) and exposed the old sensor. I snipped off the old sensor about 3" down from the end and connected the new sensor (which I trimmed down to about 3" long) with some heat shrink wire nuts/connectors. Let the fridge run for a day or so and confirmed the problem was solved! Oh yeah, there was no way to tell the 2 wires apart (power vs. ground) on the sensor. However there was a manufacturer's stamp on the wires. So note the orientation of the text and mark one of the wires with a sharpie on both the old and new sensor before trimming. This will give you a reference for which wires to connect when adding the new sensor to the old wires.

Easy, with included video and instructions

My 14 year old Son

We received the part just a few days after ordering, unscrewed the old filter by hand, and installed the new filter the same way.

Folowed instructions

The repair is a snap, you can watch the video and it will put you on the right path. My story is more about the service that Part Select gave me. I used a small box fan on low as a temporary fix. My model number was worn off from the box wine we store in that particular place. So I ordered the part based on looks, well it was wrong. Called Part Select and we talked, the nice lady on the other end said OH it must be this fan motor. Send us back that one, and I'll get this out too you. I'll credit your account for $7.99, and it cost me $8.99 to ship back the wrong part. Wow, the next day I received the new motor. They sent it overnight! I thought it would be 5-6 days! Unbelievable. I will use this company for any, and all my repairs.

It was easy and fast, like changing a light bulb. The directions were clear and easy to follow. Thank you.

We just pried off the fan blades and pushed on the new part. Could not have been easier. The rat has been permanently dipatched and, hopefully, that is that.

Replaced secondary inlet valve. Replacing the valve is repetitively simple, just cut the water tubes from the existing valve and insert into the new valve. Hard part is pulling the built-in fridge out of the cabinet space.

it was easy the only thing was i had to cut old harness to remove 2 wires that went to coil that had to go back in the new harness other then that a peice of cake.

My refrigerator was making a high pitched kind of howling noise. The PartSelect symptom that was closest was “unusual noise” and when I clicked that it said the evaporator fan motor fixes the symptom 32% of the time. Since my freezer fan speed sounded like it was constantly changing I went ahead and bought one which PartSelect delivered promptly. The installation video was great and although my freezer was not identical to the one in the video, the video was still very helpful. The only thing it didn’t say was how to tell if my freezer motor was the one with the thermistor although I suspect that they all are and that PartSelect is simply trying to save us money by showing us how to splice in a motor without a thermistor. Anyway, since I would have had to disassemble the freezer before buying the part to find out for sure, I just bought the one without the thermistor. This just meant I had to splice the new motor in, just like in the video. I think I would have preferred buying the motor with the thermistor even though it was more expensive. In the end my problem is solved so I’m happy. This is the third time that I’ve had to repair this GE refrigerator and PartSelect has been a valuable resource each time.

i followed a video that was on your site, the video couldn't have been easier to follow it was step by step and very easy to follow, i replaced the evaporator fan motor and everything is working fine, i did notice that the evaporator coil was frozen pretty bad when i removed the back freezer panel i am going to check it again in a couple of weeks to make sure i don't have a defrosting problem as of now everything is fine i am hoping it was just the bad fan motor causing the coil to freeze up because of no air movement over the coil

followed you online video and it was easy and simple repair only took about an hour frig is back quiet and working fine thanks also parts come fast

Replaced all the sensors in both the feezer and refrigerator.Even though it colder now it still is not cold enough.Freezer won't freeze items but is cold and refrigerator still not real cold

no brainer,watched the video,worst thing was to thaw the freezer,it was realy frosted,works like new,very happy thank you.