Models > ZICS360NXBLH > Instructions

ZICS360NXBLH General Electric Refrigerator - Instructions

Jump to:

All Instructions for the ZICS360NXBLH

Customer:: parviz from LAGUNA NIGUEL, CA
Parts Used:: WR78X20985
Difficulty Level:: A Bit Difficult
Total Repair Time:: 1- 2 hours
Tools:: Screw drivers

Ice in freezer around the seal and water dripping from freezer door.

Shut off the refrigerator and remove the two baskets in the freezer remove freezer compartment door .
I payed the door on a table this made impossible for easier
Replacement of the new seal . Especially because of the age of the refrigerator.
There was no problem reinstalling the door.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Randy from VALLEY CENTER, CA
Parts Used:: WR02X12008
Difficulty Level:: Very Difficult
Total Repair Time:: More than 2 hours

Loud whirling noises when the motor started up, then they subside (and stop) in a short time

I have not yet done the repair. After watching this repair video two problems came to mind. First I only ordered one grommet not knowing that there were two (or more I don't yet know). The second problem is that this video must be for a fridge from like the 1940, but it looks NOTHING like mine from 2008. The manual shows a bazillion parts and frankly I'm just a wee bit afraid to get started, and I am generally very handy, buuuttttttttt I don't know about this one

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Louis from LEAGUE CITY, TX
Parts Used:: 40A15
Difficulty Level:: Really Easy
Total Repair Time:: 30 - 60 mins
Tools:: Nutdriver

Change bulb

Easy

3 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: FRANK M from EASTON, PA
Parts Used:: WR57X10033
Difficulty Level:: Really Easy
Total Repair Time:: 1- 2 hours
Tools:: Nutdriver, Screw drivers, Wrench set

Ice Maker was not working

1st - checked water supply - old valve in water line was closed with sediment.
2nd - replaced water line valve and reconnected copper tubing about 1 hour
3rd. removed single outlet valve and installed the new part - about 15 minutes

Everything went well and was very easy.
Unfortunately, the ice maker still does not work.
Still trying to understand what is wrong.

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Patricia from Port Republic, MD
Parts Used:: WR57X10033
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers, Socket set, Wrench set

Small Ice cubes/Jams

My Son removed two screws, electric plug and two (2) compresion nuts. He had to bend the bracket to fit, then replace it, in reverse order except the filler tube on the new valve was of a "stabb-in" type. Job was a piece of cake and this small project, solved all our problems with the Ice maker.

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Edward from Jenks, AL
Parts Used:: WR17X1948
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Screw drivers

ice maker pump and water line leaking

I replaced both the punp and water line. the website depicting the repair parts was the best i ever worked with. The parts were high quality delivered on time and easy to install. Total job cost $30 as opposed the cost of of a service man or a new refrig.

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: james from Sanford, NC
Parts Used:: WR57X10033
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Wrench (Adjustable)

valve wouldn't allow enough water to fill ice maker.

Started with a visual inspection.
Turned off water.
Removed old valve.
Bent bracket to facilitate installation.
Installed.
Hooked up.
Tested.
Works as advertised.....

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Willie from Virginia Beach, VA
Parts Used:: WR57X10033
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers, Wrench set

Ice maker traydid not fill with water

Unplug electrical power to refrigerator. Disconnected electrical power to water valve, Disconnected water inlet and out let lines from valve. Remove screw holding valve on refrigerator, removed and replaced water valve with screw. Connected inlet and outlet water lines, turned on water and checked for leaks. Connected electrical power to water valve, plug in electrical power to the refrogerator. Ice maker tray fill, made ice.

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Fred from Crawfordsville, IN
Parts Used:: WR57X10033
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Wrench set

No water to icemaker

Shut the water off, removed two screws,removed the inlet, from the water valve then the line from the valve to the ice maker. Then you reverce these steps and you are done. The shipping time was the best I have ever seen. Thanks

2 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Roscoe G from ROCHESTER, NY
Parts Used:: 40A15
Difficulty Level:: Very Easy
Total Repair Time:: Less than 15 mins

Light burnt out.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

2 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Jack from Lake Helen, FL
Parts Used:: WR57X10033
Difficulty Level:: A Bit Difficult
Total Repair Time:: 1- 2 hours
Tools:: Screw drivers, Socket set, Wrench (Adjustable)

Mounting bracket did not fit. Retainer for water input looked like a thread protector.

Put bracket on workbench and hit two or three times with hammer. Glad I did not remove water inlet retainer from part, it can very easily be mistaken for a thread protector.

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: larrie from punta gorda, FL
Parts Used:: WR57X10033
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver, Pliers

ice maker just stopped

part arrived on schedule,

1 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: olin from forest city, NC
Parts Used:: WR57X10033
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Screw drivers

Ice maker not working

First i shut the water valve off going to the fridge, I then removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then i took the water line loose to the element, reverse the prosses and put all back on new element and installed,

1 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Paulette from Crandall, GA
Parts Used:: WR57X10033
Difficulty Level:: A Bit Difficult
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers, Wrench (Adjustable)

Had never installed one before and was not sure which was top or bottom. The piece was made different than the original

Unhooked power to valve
Removed old valve by taking out 2 screws.
Used adjustable wrench to remove water lines. Then reversed and hooked everything back up

2 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Tom from Dahlonega, GA
Parts Used:: WR57X10033
Difficulty Level:: A Bit Difficult
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers, Wrench set

did not work, not sure what the problem is

water runs in now but still does not make cubes. just keeps dripping until I shut the water off.

Was this instruction helpful to you?

All Instructions for the ZICS360NXBLH