RIE24VGBBFSV General Electric Refrigerator - Instructions

Slid the new shelf in.

The right side of the three left three tines must be shaved about 1/8" to allow the ice remover blades to pass unimpeded.The part should be manufactured better.

We had to pop out the insert module that was cracked, which was fairly easy. Then we needed to insert the new insert module. It was necessary to pull the side of the shelf while trying to snap in the new part. It was a bit difficult, but we finally were successful and we are very pleased.

its like im doing a puzzle coz i need to disassemble the other parts but i did it so quick.

Took the tray out, removed three screws, popped the front tray out, installed the deflector, and put it back together. Done in less than 15 minutes and my wife is ecstatic that our dispenser works again.

Once the icebin is removed, the disassembly is pretty straight forward:
-Remove all ice and allow the ice bin to reach room temperature, because frozen plastic will crack easily.
-Remove the 2 philips screws on the bottom front and release the 2 tabs on the top of the cover unit.
-Disengage the steel rod, but first make note of the spring position.
-Lift the inner assembly out from the main front bin unit, which will remove the ice screw in the process.
-Disengage the ice screw and carefully twist the crusher plate around the screw.
-Manipulate the new crusher plate around the flanges of the screw, be patient, as this can be a time consuming endeavor until you finally find the right twisting location to enable the new crusher plate to clear the flanges of the screw.
-Once in position, reattach the entire assembly and rod back into place.
-Just take your time and make note of all removed component locations.

I watched the video online and it said there were three sensors in the refrigerator, two in the freezer and one in the refrigerator. I only ordered one sensor and was going to try the one in the refrigerator first. He said the upper one in the freezer is the most difficult, but is usually the problem. So, I replaced the upper sensor and tried restarting the unit. Everything went well and it fixed the problem.

Part: Dispenser Crusher cover: after whatch the movie on line: How to change the dispenser crusher cover, was very easy to do the job. The video is excelent and show in details wht to do. No problem at all. Changed the part, fixed the problem, works as a brand new.

Empty ice. Removed cover 2 screws.Replaced cover & that was it

removed ice bucket from frig. removed screws to dis assemble the box to get to the auger assembly,removed stripped nut replaced reassembled be care not to let the rest of the assembly fall from auger there are a lot of blades and spacers to try to get back to proper position.

took off the front panel, removed the auger and front piece, removed the pin and spring and installed them on to the new piece and then put everything back together

Like I said I was getting too much ice. Typed it in on google and this site was one of the listings. I went to your site and found out the ice crusher cover was broken. The broken pieces in my glass with the ice cubes was another indication but I didn't know what it was called. I watched the video before ordering and I figured I could do this so I ordered the part. 3 days later it was here so I took the ice bin out of the freezer and let it get warmed up like the guy said in the video. I watched the video while the part warmed up. Now its time to start. I kepted the video on the computer screen just in case. I took my time and about 30 min I was making ice again. "WATCH THE VIDEO" Thanks for having this for me to watch. Made the job a piece of cake!

I made my wife fix it.

Watched an online video that I had seen before that helped immensely step by step, I fixed before and now just lowered freezer setting so ice bucket doesn’t get as full and freeze the deflector and jam deflector, causing it to break.

I watched the video a couple of times and followed the instructions exactly and the repair was very simple. This repair took me a bit more time than I thought it would just because I followed the steps methodically.

But the video was perfect to guide me through the procedure to replace this part. One of the longest parts was removing the shelving and food storage bins, cleaning them, drying them and then putting them back in after the tank was installed.