RCE25RGBBFNB General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Bobbie from Highlands Ranch, CO
- Parts Used:
- WR17X11505
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken Disp
Replaced crusher disp, but had to order the back plate(didn't realize it was two piece) waiting for that part. It was very easy to do. Had to use two drivers to pop out of ice bucket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Los Angeles, CA
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door flapper would not self-close
I replaced the original solenoid, which had rusted into one solid piece. OMG how easy was that!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Lewisville, TX
- Parts Used:
- WR17X11505
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice drawer crusher dispenser cover lid broke and allowing ice to freely drop from dispenser
Ordered ice crusher dispenser cover removed 3 screws and face plate of ice crusher was easily replaced and again working like new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryan from Fairfax, VA
- Parts Used:
- WR62X10055
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Freezer frosting up around ice dispenser chute.
Ordered new solenoid so the flap would close. That did the trick.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alice from Brookeland, TX
- Parts Used:
- WR17X11497
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Replaced part had cracked & would no longer allow ice dispensing . The icemaker continued to make & drop ice into the ice bucket.
Loosened screws to removed the cracked part & the rotating arm attached to the ice bucket. It tooke a few minutes to figure out how to manipulate the rotating arm through the irregular opening on the part being replaced. After that, putting all parts back in place & tightening 3 small screws to secure parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Lacey, WA
- Parts Used:
- WR17X11505
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Icemaker parts were cracked after use
I had to replace the whole tray. Required complete disassembly and reassembly. Simple to do. No problems whatsoever!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Shelton, CT
- Parts Used:
- WR82X10103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
brand new ge refrigerator delivered with broken access cover. cost 6.95 so i repaced it myself.
removed 6 screws and repaced cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Colleyville, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No water through door dispenser
Replaced flapper valve per website instructions. GE factory technician took two weeks to get here, charged over $100 for the call and told us we needed a new refrigerator door at a cost of over $500 to fix the problem. We sent him packing. After visiting the PartSelect website, the $5.88 PartSelect flapper valve fixed the problem. Amazing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from auburndale, FL
- Parts Used:
- WR71X10764
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken door bin
looked up the part on your site which was very quick and easy. Ordered the part and it came quickly and my installation was just as quick. Greatful for your web site Regards John
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shelly from WATERLOO, IN
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The ice flapper would not go close .
remove the front of were the ice and water comes out
then un scerw 4 scerw and the solenoid slides out unhook the wires and put the new one in
then un scerw 4 scerw and the solenoid slides out unhook the wires and put the new one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benjamin from Goldsboro, NC
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice flap in door wouldn't close
Take the face (the part with the buttons on the outside) off, disconnect wired connectors (three), take the screws out of the part behind that (4), and then find the solenoid value (on the right). It's attached with three screws. Mine was rusted beyond belief. I knew this was the problem, ordered a new solenoid valve, put it back in place with three screws (use new screws that fit, not the old rusty ones if possible). When testing, make sure you give the flap a couple of seconds to close. There is a delay, and I initially wasn't patient enough so I had to disassemble and assemble an extra time because of this.
Simply put: If your solenoid value is rusted and the value won't operate smoothly, order the part and install it. This is as easy as any repair could be.
Simply put: If your solenoid value is rusted and the value won't operate smoothly, order the part and install it. This is as easy as any repair could be.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert J. from Darlington, SC
- Parts Used:
- WR71X10764
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Broken shelf insert
Snapped it into place. Nothing to it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from Norfolk, VA
- Parts Used:
- WR71X10764
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Shelf broke
I just snapped in the new side to the shelf ...very simple and easy:-)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from Henderson, NY
- Parts Used:
- WR29X10085
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
ice maker was making no ice.
snapped in the new stripper arm where the defected one was.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from TYLER, TX
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Your video was wrong. Your step was to remove exterior frame on ice/water outlet. No need to remove.Wasted too much time trying to remove.
Remove control panel.
Remove four screw in control panel bracket.
Remove to bottom screws at bottom of solinid loose top screw.
Replace all screws.
Remove four screw in control panel bracket.
Remove to bottom screws at bottom of solinid loose top screw.
Replace all screws.
Was this instruction helpful to you?
Thank you for voting!