RCA25RGBBFNB General Electric Refrigerator - Instructions

follow the easy instructions replace 3 temperature sensors cut the wires and crimp them with new sensor and it works like new

Take off all , then install.. following the version..

took off the front panel, removed the auger and front piece, removed the pin and spring and installed them on to the new piece and then put everything back together

FOLLOW INSTRUCTIONS OF YOUR VIDEO

Like I said I was getting too much ice. Typed it in on google and this site was one of the listings. I went to your site and found out the ice crusher cover was broken. The broken pieces in my glass with the ice cubes was another indication but I didn't know what it was called. I watched the video before ordering and I figured I could do this so I ordered the part. 3 days later it was here so I took the ice bin out of the freezer and let it get warmed up like the guy said in the video. I watched the video while the part warmed up. Now its time to start. I kepted the video on the computer screen just in case. I took my time and about 30 min I was making ice again. "WATCH THE VIDEO" Thanks for having this for me to watch. Made the job a piece of cake!

removed ice bucket from frig. removed screws to dis assemble the box to get to the auger assembly,removed stripped nut replaced reassembled be care not to let the rest of the assembly fall from auger there are a lot of blades and spacers to try to get back to proper position.

New parts just snapped in place. Perfect fit.

Took the tray out, removed three screws, popped the front tray out, installed the deflector, and put it back together. Done in less than 15 minutes and my wife is ecstatic that our dispenser works again.

Once the icebin is removed, the disassembly is pretty straight forward:
-Remove all ice and allow the ice bin to reach room temperature, because frozen plastic will crack easily.
-Remove the 2 philips screws on the bottom front and release the 2 tabs on the top of the cover unit.
-Disengage the steel rod, but first make note of the spring position.
-Lift the inner assembly out from the main front bin unit, which will remove the ice screw in the process.
-Disengage the ice screw and carefully twist the crusher plate around the screw.
-Manipulate the new crusher plate around the flanges of the screw, be patient, as this can be a time consuming endeavor until you finally find the right twisting location to enable the new crusher plate to clear the flanges of the screw.
-Once in position, reattach the entire assembly and rod back into place.
-Just take your time and make note of all removed component locations.

Empty ice. Removed cover 2 screws.Replaced cover & that was it

After inspection of the new door recess assembly, I realized that I could use sidecutters (electronic assembly type) and 'clip' off the inward lock tabs of the old recess assembly and disengage it from the crank door arm without any further disassembly of the refrigerator door. It was easy to 'unhitch' the tang from the crank arm and wiggle it out through the external opening of the ice/water dispenser compartment. I reversed the process and inserted the new assembly through the external opening of the compartment. The new door recess assembly snapped into place on the crank arm and fit tightly against the ice chute opening, correcting the issue caused by aging distortion of the old rubber seal cup portion of the door recess assembly.

Part: Dispenser Crusher cover: after whatch the movie on line: How to change the dispenser crusher cover, was very easy to do the job. The video is excelent and show in details wht to do. No problem at all. Changed the part, fixed the problem, works as a brand new.

I watched the video online and it said there were three sensors in the refrigerator, two in the freezer and one in the refrigerator. I only ordered one sensor and was going to try the one in the refrigerator first. He said the upper one in the freezer is the most difficult, but is usually the problem. So, I replaced the upper sensor and tried restarting the unit. Everything went well and it fixed the problem.

The right side of the three left three tines must be shaved about 1/8" to allow the ice remover blades to pass unimpeded.The part should be manufactured better.

Went exactly by the video. Perfect job, you send the installation video with the part. You watch the video before or during, goof proof, took longer to disassemble than to replace the part.