RCA25RGBBFKB General Electric Refrigerator - Instructions

Followed the instructions in the operator's manual to remove the door. Popped off cover of top hinge. Unscrewed the two screws holding pin down with socket set. Took off door. Unscrewed broken door stop with TORX socket. Replaced new door stop and reversed the process to replace the door. Very simple repair.

Changing out solenoid was very easy, but you don't have to remove trim ring and it didn't fix my problem. Turns out a relay fell out of its holder in the piece you have after removing the 4 screws per the video.

Went exactly by the video. Perfect job, you send the installation video with the part. You watch the video before or during, goof proof, took longer to disassemble than to replace the part.

its like im doing a puzzle coz i need to disassemble the other parts but i did it so quick.

Watched an online video that I had seen before that helped immensely step by step, I fixed before and now just lowered freezer setting so ice bucket doesn’t get as full and freeze the deflector and jam deflector, causing it to break.

I made my wife fix it.

First, turn off power - since I did not want to pull the refrigerator out on my wood floor I tripped the circuit breaker to that circuit and opened door to make sure interior light was off (ensuring power was off). This unit has a bottom freezer, I took out all shelves, ice maker and all parts in the way of accessing back of interior of freezer section. Removed back plastic section by removing one screw in middle top of back panel and prying it out. This was a bit difficult as it was in there a bit tight but once the plastic warmed up it pulled out ok. This revealed the compressor section and temp sensor that was attached to the copper coils with of all things - a zip tie! In pictures of this that I looked at on various web sites the sensor was on a metal bracket attached to the coil so it made me wonder if tf the factory took a shortcut? I cut the old sensor wire, stripped the two wires 1/2", and connected them to the new sensor wire with butt connectors, I put some silicone into the ends of the butt connectors to prevent moisture from entering into connectors and wrapped the connection in black electrical tape. I then "attached" the sensor to the coil using a zip tie, put the plastic back piece back on, inserted everything I took out and put power back to refrigerator. It's been 3 days and temp of refrigerator is stable, ice maker not clogging up, and compressor not running all the time! So far so good.

Snapped it into place. Nothing to it!

remove the front of were the ice and water comes out
then un scerw 4 scerw and the solenoid slides out unhook the wires and put the new one in

Take the face (the part with the buttons on the outside) off, disconnect wired connectors (three), take the screws out of the part behind that (4), and then find the solenoid value (on the right). It's attached with three screws. Mine was rusted beyond belief. I knew this was the problem, ordered a new solenoid valve, put it back in place with three screws (use new screws that fit, not the old rusty ones if possible). When testing, make sure you give the flap a couple of seconds to close. There is a delay, and I initially wasn't patient enough so I had to disassemble and assemble an extra time because of this.

Simply put: If your solenoid value is rusted and the value won't operate smoothly, order the part and install it. This is as easy as any repair could be.

looked up the part on your site which was very quick and easy. Ordered the part and it came quickly and my installation was just as quick. Greatful for your web site Regards John

Replaced flapper valve per website instructions. GE factory technician took two weeks to get here, charged over $100 for the call and told us we needed a new refrigerator door at a cost of over $500 to fix the problem. We sent him packing. After visiting the PartSelect website, the $5.88 PartSelect flapper valve fixed the problem. Amazing.

Loosened screws to removed the cracked part & the rotating arm attached to the ice bucket. It tooke a few minutes to figure out how to manipulate the rotating arm through the irregular opening on the part being replaced. After that, putting all parts back in place & tightening 3 small screws to secure parts.

I had to replace the whole tray. Required complete disassembly and reassembly. Simple to do. No problems whatsoever!!

Ordered new solenoid so the flap would close. That did the trick.