RCA24KGBBFWW General Electric Refrigerator - Instructions

Take off all , then install.. following the version..

First:
Remove all shelf’s and drawers from fridge inside that were on the way of the water tank
Second:
Pull the fridge from the wall
Turn off the water supply:
Unplugged the power supply
Third:
Remove the cardboard cover at bottom of the fridge on the back for better access to the water pipes
From the front remove the toe kick for better access at the water pipes
Disconnected the water pipe at the front left side, use a rag or paper towel to hold the water that may drip ( bigger pipe)
Remove the covers on the top of the water tank inside the fridge
Disconnected the water pipe at the back left side ( smaller pipe)
Unscrew the water tank (two screws)
Pull the water tank out with the water pipes attached
Fourth:
Install the new water tank assembly , make sure the pipes goes on the hole at the right side and reaches the from and back
Connect pipes until the line that shows on the pipes
Screw back the new water tank
Put the protections back on the top
Plug the fridge and open the water supply to make sure there is no water leaks
The water is ready to be use

Replaced freezer door gasket and fresh food door gasket. fresh food door gasket is works OK. BUT cannot stop new freezer door gasket from leaking cold air . Looked at three or four you tube videos for instructions and seemed to work well. I took off the freezer gasket and turned it over (end for end) and it still has a cold air leak. help

removed ice bucket from frig. removed screws to dis assemble the box to get to the auger assembly,removed stripped nut replaced reassembled be care not to let the rest of the assembly fall from auger there are a lot of blades and spacers to try to get back to proper position.

took off the front panel, removed the auger and front piece, removed the pin and spring and installed them on to the new piece and then put everything back together

I had to take off the back lower grate which was roughly six 1/4 screws. Disconnect the water lines to the ice maker and the filter manifold. Remove the manifold from the inside of the refrigerator by removing two 1/4” screws. Pull the manifold and line out from the inside of the refrigerator and reverse the process for the replacement.

I watched the video online and it said there were three sensors in the refrigerator, two in the freezer and one in the refrigerator. I only ordered one sensor and was going to try the one in the refrigerator first. He said the upper one in the freezer is the most difficult, but is usually the problem. So, I replaced the upper sensor and tried restarting the unit. Everything went well and it fixed the problem.

We had to pop out the insert module that was cracked, which was fairly easy. Then we needed to insert the new insert module. It was necessary to pull the side of the shelf while trying to snap in the new part. It was a bit difficult, but we finally were successful and we are very pleased.

Once the icebin is removed, the disassembly is pretty straight forward:
-Remove all ice and allow the ice bin to reach room temperature, because frozen plastic will crack easily.
-Remove the 2 philips screws on the bottom front and release the 2 tabs on the top of the cover unit.
-Disengage the steel rod, but first make note of the spring position.
-Lift the inner assembly out from the main front bin unit, which will remove the ice screw in the process.
-Disengage the ice screw and carefully twist the crusher plate around the screw.
-Manipulate the new crusher plate around the flanges of the screw, be patient, as this can be a time consuming endeavor until you finally find the right twisting location to enable the new crusher plate to clear the flanges of the screw.
-Once in position, reattach the entire assembly and rod back into place.
-Just take your time and make note of all removed component locations.

The right side of the three left three tines must be shaved about 1/8" to allow the ice remover blades to pass unimpeded.The part should be manufactured better.

I made my wife fix it.

Watched an online video that I had seen before that helped immensely step by step, I fixed before and now just lowered freezer setting so ice bucket doesn’t get as full and freeze the deflector and jam deflector, causing it to break.

replaced the water filter head and water lines which were fairly easy. Glad Partselect had was I was looking for and it arrived quickly.

Turn-off water and disconnect main water line to inlet-tube.
Removed lower-back panel of the fridge with a screw driver and disconnected the hose with a small wrench to the main fridge water valve.

On th top-left, back of the fridge, removed screws to the small plate where the hoses enter for the water filter. In the fridge, removed the water filter, then removed the plastic panel above the filter - it snaps out. There are two screws to remove, then grasp and pull the assembly and hoses out. reverse the process for an easy install.

I was not able to put the small plate onthe back, top-left of the fridge back on. It's a tight fit and I didn't want to pinch the lines. Not doing that, though, may limit how your fridge rolls back to where it was, because the lines will stick-out a couple of inches.

Like I said I was getting too much ice. Typed it in on google and this site was one of the listings. I went to your site and found out the ice crusher cover was broken. The broken pieces in my glass with the ice cubes was another indication but I didn't know what it was called. I watched the video before ordering and I figured I could do this so I ordered the part. 3 days later it was here so I took the ice bin out of the freezer and let it get warmed up like the guy said in the video. I watched the video while the part warmed up. Now its time to start. I kepted the video on the computer screen just in case. I took my time and about 30 min I was making ice again. "WATCH THE VIDEO" Thanks for having this for me to watch. Made the job a piece of cake!