PFSF5NFCACC General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from Island Lake, IL
- Parts Used:
- WR55X10025
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
frige too cold
changed sensors did not repair problem,replaced damper with mechanical damper fixed problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from myrtle beach, SC
- Parts Used:
- WR57X10086
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
ice maker not making ice
I looked up appliance on internet,diagram only showed the inlet valve and ice maker in schematic.I ck'd to see if water was getting to valve(it was)but wasn't getting to ice maker,thus I replaced the valve and it solved the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Chimacum, WA
- Parts Used:
- WR55X10025
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
fridge to warm
followed part select video instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from silver bay, MN
- Parts Used:
- WR55X10025
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Fridge Side Freezing/Too Cold
Followed the repair video, was spot on!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason Mcgee from Catawissa, MO
- Parts Used:
- WR55X10025
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
freezer would not defrost or maintain temperature
luckly i have a bit of experience in refrigeration im an hvac technician by trade. this repair was a bit tricky in that i did not know at first if it was a Temperature Sensor issue or the main control board. I had tested the defrost termination thermostat and the defrost heater and as i suspected they were ok. Next i wanted to test the thermistors (temp sensors) it is hard to find technical data on these fridges. I needed to test the thermistors resistance @ a certian temperature to ensure they were working properly but where do u get such data? I also wanted to know some information about the logic programmed into the board (i.e when do you initiate defrost etc. . .). I had no such luck so i figured since i tested the defrost heater and thermostat and they were ok and all of the evap fans and such were working i'd order a circuit board and new thermistors. Got the CORRECT PARTS from this site in 2 business days and my fridge is working great! changing the parts was really easy, figuring out which parts to change was the only difficult thing about this job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brandon from Bruceton Mills, WV
- Parts Used:
- WR55X10025
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Defroster stopped working and iced up evaporator coil
I have a GE Profile French door refrig. It's only about 4 yrs old and the defroster stopped working. I read the other repair stories and was able to narrow it down to either the temp sensor, defrost timer, or main board. The refrig section was up to about 47 degrees and freezer was around 25. I could tell it was trying to cool but couldn't. So I tried the temp sensor first. I cut and spliced the new sensor on the outlet of the Evap. Coil and it took about 15 mins. Turned refrig back on and waited. The coil started to ice over after about 5 hrs I left the back panel off so I could see if and when then heater kicked on. After about 8 hrs I looked in and saw a faint glow and water trickling down and running out the drain. Turned out the sensor was bad and wasn't telling the main board it needed to defrost. I would try the sensor if you are having the same issues before spending a lot of money on the main board, defrost heater and or timer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from Brentwood, MD
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench set
freezer and refrigerator wasn't cold
Replaced all the sensors in both the feezer and refrigerator.Even though it colder now it still is not cold enough.Freezer won't freeze items but is cold and refrigerator still not real cold
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- W Craig from Diamondhead, MS
- Parts Used:
- MWFP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Filter needed replacing
Folowed instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from selbyville, DE
- Parts Used:
- WR17X22070
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
water dispensed slow and filters too expensive and not very reliable
I just unscrewed filter and screwed in filter bypass
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- donnie from metairie, LA
- Parts Used:
- MWFP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced filter
none required
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Rancho Cordova, CA
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator freezing.
Temp. Sensor was under an egg shaped cover on the left side wall in the refrigerator. Remove the cover, cut the two wires to the old sensor and remove it. Connect the new sensor to the two wires using butt connectors. Replace cover and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Saint Charles, IL
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
refrige ws too cold
as per video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from La Grande, OR
- Parts Used:
- MWFP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
water filter was aged and needed a replacement
unscrew filter and replace the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Natalia from Mount Pleasant, SC
- Parts Used:
- MWFP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Water filter needed replacement
Removed the old filter. Filled the new one with water and put it in theplace of an old one. Flushed the system with 1 gallon of water.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christopher from collegeville, PA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no light in freezer
Connected the 2 wires and pushed in the switch until it clicked.
Was this instruction helpful to you?
Thank you for voting!