PFCA1NJZHDSS General Electric Refrigerator - Instructions

First, removed all items in the freezer, placed into a cooler. Removed basket and door from the glide rails. Installed new divider using two supplied screws with a nut driver. Be sure to install support bar first and align the divider by loading at an angle, push into place. Reinstalled shelf and icemaker tray, door, and basket. Can be a little tricky to install if you don't do the support bar first, and removing the door seemed necessary for adequate access to the interior of freezer.

There were no instructions on how to relpace the divider guide so it took me a while to realize that I had to remove the guide under the ice maker first. Once that was done the metal bar that supports the front of the divider guide and the divider itself could be positioned. It did take a little force to push the guide into its proper vertical position. After that the the guide under the ice maker could be replaced.

In replacing the freezer door I wasn't careful to pull both glides out together so the geared tracking mechanism came apart. Once that was put back together and carefully pulled out the freezer door was able to be replaced.

installed the new door shelf

Extremely easy repair, the hardest part was getting the old switch out. I used a pair of needle nose pliers to squeeze the tabs in and it came right out.

Remove the top cover above the door by lifting it slightly and pulling forward. I used a mirror to make sure that there was nothing in the way of accessing the switch from above. I used a blade screwdriver to press against the switch retainer on the topside, while GENTLY prying from below with another blade screwdriver to get the switch dislodged. Once the retainer was past the opening, I wiggled the switch downward and then rotated it to the left when the rounded top right edge of the switch was visible. This allowed the wiring to the connector to pass thru the hole. I pushed the wiring from the top and pulled from below to get the connector below the opening for the switch. I then unplugged the switch, plugged in the new switch and reversed the removal process feeding the connector thru first then rotating the switch to the right to get the rounded edge of the switch thru the opening, then pressed the switch up into the opening until it snapped into place. Total time less than 10 minutes.

with a jewelry screwdriver I pried the lock tab in and pulled switch down carefully, the hardest part was that the power wire connector was stuck on good but the pliers and the jewelry screwdriver was its match for a bout 5 minute for one connection a simple pull off prong connection. After the wire connected back to switch it popped back in SNAPP

Removed ice bucket, and unplugged ice maker. Removed light cover. Removed ice maker. Pulled fan blades straight up and removed. Pushed new blades on to motor shaft. Fairly easy .

took a little more effort than the video show to remove old module and replace new. Works fine now.

got new filter

Took out the MFW filter.
Screwed in the MFW bypass.
Dispensed several gallons of water.
Saw good flow of water.
Removed MFW bypass.
Replaced MFW filter.
Our water flow was back to normal.

It was way to ez to install only a couple of minutes that's it

Took cover off, pushed blade on, and replaced cover

Totally followed the instructions of the video that came with the sensor. Unplugged the the fridge, defrosted the freezer. Cut off the main sensor that usually is the one that goes out. Installed the the new sensor with new wire terminals, crimped them and covered with electrical tape. Fridge works like a charm. Partsselect is excellent. Saved me a few hundred dollars versus having a GE Tech come and do it.

Turned the old filter loose, removed the adapter from it, put the adapter on the new filter and turned the new filter back into place.

So we ordered a replacement "PS2577898 GLASS COVER Vegetable PAN" and they sent us the wrong part. It sort of fits over the vegetable drawers, but our GE Fridge model has curved sides and these guys sent us a glass cover that is a perfect rectangle, which sticks out above the grooves where it's supposed to go. After a month of waiting, though, we just didn't care anymore and decided to use the part that arrived. Asking for the correct replacement may take us into 2021...