GTS18GBEJRWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Victor from Fort Myers, FL
- Parts Used:
- WR23X37285
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
light in freezer section not working
Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juaneese from Madison, TN
- Parts Used:
- WR17X11662
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Broken Vegetable Pan Cover
I replaced the Vegetable Pan Cover myself and it looks and fits great. The hardest job was unloading so that the previous cover could be taken out. I was proud of myself for being able to do this job myself without any help. Ordering and receiving the part was so easy that I will always use Parts Select. Thanks again. Juaneese
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dewey from Laurel, MD
- Parts Used:
- WR24X10228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replacement gasket
I took it right out of the framed box to keep the gasket in shape and snapped it back on the gasket mount on the freezer door it took 5 minutes or less perfect fit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KIRK from Malibu, CA
- Parts Used:
- WR9X502
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Freezer work refierator compartment is warm
Defrost timer is hidden in the control panel in the refrigerator top middle. Turn to off and remove two screws which are hidden behind white tabs. I had to pry the old timer from the plug with a screw driver because it was tight. Try not to short across the terminals. Plug in the new timer. Replace it in the clip where you got old one and reinstall the controls. The freezer was still all frosted up so I had to remove the cover and defrost it with a hair dryer to get it to work. Then I turned it on and it works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- N Smith from Chicago, IL
- Parts Used:
- WR24X10236
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
replaced the refrigerator door gasket
The original gasket had ripped and the magnet strip was hanging out. Following information from several youtube video clips & suggestion from the seller, I soaked the gasket in a tub of hot water for 30min to make it more pliable. After removing the old gasket, I put on the new, which only appeared to just snap into a metal tract. However the door couldn't seal. There were big gaps. That is when I realized that the gasket was still rigid. So I took a heat gun and carefully blew hot air on the gasket as I pulled it out enough for the metal edge of the gasket to attach itself to the refrigerator. Took quite a while to get it to seal correctly, but seems to be working well now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MAE from FARMERS BRANCH, TX
- Parts Used:
- WR24X10236, WR24X10228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
The old gaskets were not sealing properly.
removed the old gaskets with the putty knife to pry it loose then pulled the old gaskets off. Soaked the new gaskets in slightly boiling water to make them better able to straighten out and then installed by lining them up and pressing them in place, making sure they were lined up and that they were in the track provided for them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from east hanover, NJ
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
refig light did not work
per your instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Reese from Coconut Creek, FL
- Parts Used:
- WR9X502
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
defrost timer was bad
repalaced the old one with the new one. easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- r from Bronx, NY
- Parts Used:
- WR24X10236, WR24X10228
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Gaskets needed replacement to maintain correct temperature in the refrigerator and freezer
Removing the old gaskets was very simple. Replacing the fresh door gasket was the most time consuming. It would have been easier if I had help, it took a some time and patience. The gasket works perfectly. The freezer gasket was easy to replace. The gaskets fit perfectly, thank you. For the ladies out there, you if I can do it, so can you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry from West Seneca, NY
- Parts Used:
- WR9X502
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Frezzer would freeze up, refrigerator stayed cold, solved the problem. Now the refrigerator seems to be running more than usual.
Checked the defroster coil which is located behind the rear panel in the freezer compartment, it was still working. Followed the schematics down to the defrost timer, which is located in the lower front of the refrigerator and tried that. Plugged in the new part and the problem is solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Simpsonville, SC
- Parts Used:
- WR23X37285
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light switch quit working
removed the inside fridge electrical panel and swapped switches
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Andrews, NC
- Parts Used:
- WR9X502
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Refrigerator and freezer too warm
1) This is a built-in refrigerator with the compressor, coils, etc. at the top. Turn off the breaker to the fridge. 2) Remove the front panel off the top (just push up and pull out). 3) Removed 2 screws to the old timer and carefully remove the plug. Plug the new timer in and screw in. 4) Since our fridge was heavily frosted up, we moved everything to another refrigerator and coolers and kept the refrigerator off until all panels were room temperature. 5) If you haven't cleaned the coil in a while, vacuum it with a soft brush attachment. 6) Turned back on and the refrigerator is cooler than ever!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANTHONY from NEW EGYPT, NJ
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
sticky switch
easy pry out, disconnect wiring, connect on new switch and press in switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Boris from East Lansing, MI
- Parts Used:
- WR12X10108
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no problem
easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Carlsbad, CA
- Parts Used:
- WR17X11662
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Sides of old shelf cracked
Pulled out old shelf and put in new one. However the new shelf is too narrow and will break at some point just like the old one. Apparently no way to fix this issue.
Was this instruction helpful to you?
Thank you for voting!