GTH18GCDCRWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Barbara from BELLEVUE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
Twice I ordered the oven light bulb & each time the light bulb was defected
I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ben from Warrior, AL
- Parts Used:
- WR9X502
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Refridgerator wouldn't cycle into defrost mode without doing it manually.
I removed the shield over the timer and the part that supported the timer. Just unpluged it and pluged in new timer and put back shield. I had already replaced the defrost heaters which had totally burned up. I also replaced the thermostat while I was making the repairs although the old one was still o.k. All the information that I needed to make the repairs I obtained through your website. After looking at several websites to compare prices-etc, I found yours to be the best overall. Thanks-a-million your website is worth it's weight in Cold Food !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from BELLVILLE, TX
- Parts Used:
- WR9X502
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
refrigerator wasn't cooling but the freezer was working properly
From instructions found on the site I was directed to the defrost timer part being bad. And from the information others posted that have had the same problem I was able to replace that part by removing the bottom grill just below the door and on the left side was the part. Removing one screw to remove the bracket from the frame and then another screw to remove the part from the bracket. I found it easier to remove the part from the bracket before I pulled the part out so I would have more room to unplug the connector. Just reverse the steps to replace the new part. It took about a day or so for the refrigerator to get to the proper temp.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gerald from ardmore, PA
- Parts Used:
- WR60X31522, WR60X46086
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
evap.motor burned out
common sense,removed plate,removed mounting bracked,unplugged,reversed order,and that was it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dustin from Marlow, OK
- Parts Used:
- WR02X27092
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom door hinge was lost during move
I had lost the bottom hinge during a move and so I rigged the hinge using an old tv antenna and the door never really quite worked right and it was VERY annoying. I stumbled upon this site and was surprised how inexpensive the part I needed was. I was very impressed with the speed of shipping and the install took maybe 5 minutes. The fridge works as good as new. Thanks a ton!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- albert from patterson, NY
- Parts Used:
- WR02X12149, WR60X31522, WR02X12008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
Fan Motor was Noisy
4 screws in the freezer and the back panel came off then 2 more screws to take the motor off. I unpluged the old motor pluged in the new motor put the back panel back on and I was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Millbrae, CA
- Parts Used:
- WR22X10068
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door dairy was broken
Repair was a no brainer. More important, Part Select was extremely efficient. Customer Service was very helpful as my model number was not available on line. Thanks for your wonderful and prompt service. Rich L.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from HADDON HGTS, NJ
- Parts Used:
- WR60X31522, WR02X20092
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Noisy evaporator fan motor
Removed old replaced with new part. Easy Peasy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from SUFFOLK, VA
- Parts Used:
- WR12X22148
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Remove screws holding handles
Using a screw driver(Phillips) I removed screws on top and bottom. Very easy and quick parts fit like a glove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Ann from BELLVILLE, OH
- Parts Used:
- WR12X22148
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Handle broke off at top where the screws were on door.
Removed the screws, placed new handle on door, tightened screws, all done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Esparto, CA
- Parts Used:
- WR12X22148, WR01X10590
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Handle broke on the top where the screws go.This is the second handle that broke in the same place in 5 years.
Remove the top screws, with a Philips screw driver, take broken piece out. Then remove the plastic cover on bottom of handle, take the torx screw out. Now handle is off.Put new handle in place and put all three screws back in. Then install new plastic cap, and you are all done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Brookfield, IL
- Parts Used:
- WR71X2086
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no shelf in my freezer
first I ordered parts that didn't work. the return process was painless and I found the part I needed, which just popped right in!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from ORANGE, CA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Unit had stopped making ice
Ordered the icemaker replacement. unplugged the unit, followed the simple instructions and got it done in less than 30 minutes. It did take a LONG time to start making ice. But it's working now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gabriel from WASHINGTON, DC
- Parts Used:
- WR60X31522, WR02X10098
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Loud screeching noise from freezer during cooling cycle
I replaced the fan motor and one of the grommets. When I took the motor out it was clear it was failing because there were metal flakes from the motor on the fan blade. I followed the instructions on the posted video. My model did not have a removable bottom tray in the freezer so that was one less thing to do. Aside from that the video was accurate. I had two minor problems during reinstallation. First, it was very difficult to get the spring clamp back on the fan blade without pushing it against the motor. Recommend you get someone to help hold the spring open while you push it on. Second, the length of wire on the replacement was not exactly the same as the original and I had to move some wires around. Recommend you take a picture of the cable layout before disassembling.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from NANTUCKET, MA
- Parts Used:
- WR60X31522, WR02X12008, WR02X10540
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
NOISY
I FOLLOWED YOUR VIDEO............WAS EASY. THANKS
Was this instruction helpful to you?
Thank you for voting!