GTH18GBDCRBB General Electric Refrigerator - Instructions

Just put the refrigerator door shelf in. Was to happy to fix this missing piece. So glad this company was able to supply an old part.

screwed the cover on just like the original

Extremely easy repair, the hardest part was getting the old switch out. I used a pair of needle nose pliers to squeeze the tabs in and it came right out.

put the gratefruit knife behind the old switch pooped it out pluged the new one in piece of cake 5min.even vacumed the dust off the coil

First unplug freezer and empty contents, then remove the screws from the air deflector, carefully remove styrafoam air deflector block then remove back panel for easy access. Fan will be easy to switch out from there. I highly recommend the You Tube video which is where I got my basic instructions.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Slipped it it-very easy

Find a video on youtube. Remove 6 screws. Pull the Styrofoam part up before removing the panel. Unplug and Remove the fan assembly.
You will need a NUT DRIVER to take the bracket off the backing plate.
I ordered the red grommet and the red bumper. You need TWO of the red grommets if that is the problem. My freezer was about 8 years old, and the grommets were worn and compressed, the bumper was not. Replacing these parts DID NOT FIX the problem. I needed a new motor.
I probably disassembled and reassembled this stuff about 7 times before I got all the parts and tools. Each time I had to unload the freezer.

shelf just snapped into place. It was so simple, "even a caveman could do it."

Easy peasy
take the drawer out and the glass from the shelf above the drawer and the frame thet holds the glass.

Then place screwdriver at pin and knock it through. Use putty knife to pull old piece out. Then place new piece in and hammer the pin in place. Put frame back in, glass back in and drawer back in.

This was so easy I think it took me 2 minutes. I am not very mechanically inclined but that didn't matter! Works perfect thank you!

removed from previous veg humidity drawer the humidity scale, careful pry plastic piece from the edge until both complete edges are exposed, gently pull humidity scale away from veg humidity drawer. veg humidity drawer has vent open and closer behind the veg humidity scale, with veg humidity drawer removed firmly grasp insert triangle shaped tabs and squeeze together while pulling the veg humidity drawer vent open and closer towards the back of the drawer, once released maneuver the adjust tab out the veg humidity drawer vent. replaced old veg humidity drawer vent closer in new veg humidity drawer by maneuvering the vent closer large tab into square shaped hole till rest of vent closer and opener is in a flat position on the drawer, push firmly on vent closer and opener evenly until triangle shape tabs lock into place, next place veg humidity drawer scale on pull of veg humidity drawer place the top of the scale on the sharp edge of the drawer and push evenly down on veg humidity scale till long piece snaps in place.

Remove ice maker and all of it's accessories in order to remove the panel covering the fan. Don't drop the screws!
Unscrew the lower fan bracket. You will see the lower red rubber grommet. Hold fan motor with one hand and push the fan off the shaft and into the compartment above. Then remove the round retainer thing below it by holding it and pulling down on the motor assembly. Install new grommet on upper part. and put it all together.
REMEMBER where the fan is on the shaft. It has about one inch of shaft placement. I put mine so that most of it was above the hole that the fan goes into and about 20 percent showing below the sheet metal.
Also check to see if your fan is damaged. Mine was not.
This refrigerator has been awesome! I have had many issues but have been able to fix all of them for the last 15 years!

Separately (from a different site) purchased new compressor fan and motor. I purchased the grommets here because the other site listed the grommets as temporarily out of stock. I did watch one of the videos on PartSelect about the grommet replacement. Repair was pretty simple, biggest challenge was getting to the screw on the far side of the motor. Removed the two screws holding the fan motor into place. Removed motor and blade. Reinstalled with new fan blade, new grommet and new motor.

I followed your video and completely dismantled the refrigerator evaporator motor, fan, brackets, and grommet, I completely cleaned the refrigerator including the cooling coils. I then ordered the evaporator motor ,fan, grommets, lid bumper, and brackets. The order would take a week to arrive. In the meantime I cleaned and reassembled all the old parts, waiting for the new ones to come. Guess what! The refrigerator was quiet as a mouse. I really did not need the new parts, but I kept them anyway just for good luck. Not bad for a refrigerator that's twenty four years old.