GTH18CBEDRWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Edwin from BELLINGHAM, WA
- Parts Used:
- WR22X10068
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
replace broken door dairy
a-ok. no problems
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ronald from springfield, VT
- Parts Used:
- WR60X31522
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
noisy fan
removed cover over fan, four screws. removed two screws ,that holds fan in place,removed two more screws that holds fan in bracket,then reinstalled
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Coto de Caza, CA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Interior Light did not go on due to faulty switch
I ordered two switches, replaced both with a knife in 10 minutes. Interior light works, thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LARRY. T from KNOXVILLE, TN
- Parts Used:
- WR60X31522, WR60X46086, WR02X12008
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
intermittent loud screeching,,humming sound
removed food from freezer section removed fan guard, partially remove ice maker, remove back panel, then fan assembly,disaasembled fan motor from brackets, fan from motor, grommet from bracket. assembled grommet in bracket, fan blade on motor, motor in bracket, fan assembly back in compartment, installed back panel,then ice maker, replaced fan guard and food. no more noise.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joan from STERLING HTS, MI
- Parts Used:
- WR60X31522, WR60X46086
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Fan not working
Took out old put new in. Watched a u tube, no problems
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from MELBOURNE BCH, FL
- Parts Used:
- WR60X10238, WR60X10207
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Motor making screeching sounds
Removed back panel
Unplugged wires to motor
Removed motor & fan assembly
Attached new fan to new motor
Attached motor to motor housing
Reattached wires
Reinstalled back panel
Unplugged wires to motor
Removed motor & fan assembly
Attached new fan to new motor
Attached motor to motor housing
Reattached wires
Reinstalled back panel
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mackenzie from Williston, ND
- Parts Used:
- WR09X20002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Compressor would randomly not turn on. Fridge too warm sometimes.
Replace temperature control. That fixed it. Also, removed plastic bag obstructing air vent in freezer which added performance. Fridge works good now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eileen from Coto de Caza, CA
- Parts Used:
- WR23X37285
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
switchlight on my refrigerator was not working
I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, it was just a matter of plugging in the new switchlight , which was very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Ridgecrest, CA
- Parts Used:
- WR60X31522, WR02X12008, WR60X46086
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Freezer was not freezing food.
Inspected freezer because food was not freezing, getting cold, but not freezing. Noticed fan was not blowing air, but making a little motor noise, like it's trying to turn. Removed cover panel, and found the fan blade rubbing on the panel, fan shaft was worn out and very loose, wobley. That told me the fan needed to be replaced. Found part on the GE Partselect website and ordered the parts via the website order process. This was easy. The parts were shipped quickley and were at my front door the next day. Couldn't believe it. The actual process was very easy: Remove cover, remove bracket holding fan motor, remove and replace motor, re-assemble parts. About 20-25 minutes from start to finish. Freezer is working like it's suppose to.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from TEXARKANA, AR
- Parts Used:
- WR17X11890, WR17X11889
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
I never had Door shelving
Just popped them in their slots. Very easy and it made my refrigerator brand new again.. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bradley from Cedarburg, WI
- Parts Used:
- WR60X10207, WR02X12149
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Condensor fan blade cracked, blade was sheared off.
First, remove the cardboard cover on the back, lower portion of the refrigerator.
Next, locate the condensor fan motor assembly and blade. (Right side as you are facing)
Using a pliers, hold the shaft to keep it from turning and prevent damage to the motor. Using a screwdriver, slide the old ring compression on the blade shaft toward the motor (away from the fan blades) to loosen.
Remove old blade from the shaft by firmly grasping the motor shaft with a pliers (to prevent from damaging) and pull the blade assembly off.
Reverse the above steps to attach the new blade.
Next, locate the condensor fan motor assembly and blade. (Right side as you are facing)
Using a pliers, hold the shaft to keep it from turning and prevent damage to the motor. Using a screwdriver, slide the old ring compression on the blade shaft toward the motor (away from the fan blades) to loosen.
Remove old blade from the shaft by firmly grasping the motor shaft with a pliers (to prevent from damaging) and pull the blade assembly off.
Reverse the above steps to attach the new blade.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from humble, TX
- Parts Used:
- WR17X11889
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing part
I order the small part and installed it myself, it was very easy with "part select". I will refer them and use them in the future. Thanks parts select.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Boyd from Blaine, WA
- Parts Used:
- WR09X20002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Could not adjust temperature
Replaced temp controller
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sophie from WASHINGTON, DC
- Parts Used:
- WR17X11890
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken freezee door shelf
Click shelf into place!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry from DOUGLASVILLE, GA
- Parts Used:
- WR09X20002
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Fridge never cuts off.freeze everything inside of fridge.
To remove the temp sensor.2 Phillip head screws not remove the cover inside fridge .the temp control knob cover.removed that and unplugged switch.installed new switch.reinstalled cover.
Was this instruction helpful to you?
Thank you for voting!