GTH18CBC2RBB General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mackenzie from Williston, ND
- Parts Used:
- WR09X20002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Compressor would randomly not turn on. Fridge too warm sometimes.
Replace temperature control. That fixed it. Also, removed plastic bag obstructing air vent in freezer which added performance. Fridge works good now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Harrisburg, PA
- Parts Used:
- WR32X10398
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old cover was cracked and needed replaced
The repair only required removing nthe old cover and installing the new one. What I was really surprised about is the time for delevery. I ordered the part on Friday morning around 11 AM and it was delevered by Fed Ex at 8:30 AM on Saturday morning. I am not sure how many locations they have, but this must have been close to Harrisburg, Pa.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from humble, TX
- Parts Used:
- WR17X11889
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing part
I order the small part and installed it myself, it was very easy with "part select". I will refer them and use them in the future. Thanks parts select.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Elkhart, IN
- Parts Used:
- WR17X11889
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Freezer shelf bracket broke. .
Took the bracket out of box and install it like the video showed me..very easy to install..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Ridgecrest, CA
- Parts Used:
- WR60X31522, WR02X12008, WR60X46086
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Freezer was not freezing food.
Inspected freezer because food was not freezing, getting cold, but not freezing. Noticed fan was not blowing air, but making a little motor noise, like it's trying to turn. Removed cover panel, and found the fan blade rubbing on the panel, fan shaft was worn out and very loose, wobley. That told me the fan needed to be replaced. Found part on the GE Partselect website and ordered the parts via the website order process. This was easy. The parts were shipped quickley and were at my front door the next day. Couldn't believe it. The actual process was very easy: Remove cover, remove bracket holding fan motor, remove and replace motor, re-assemble parts. About 20-25 minutes from start to finish. Freezer is working like it's suppose to.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from New York, NY
- Parts Used:
- WR50X10071
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Freezer is too hot
Open the freezer panel which attached with screwws and locate the defrost thermmostate behind the back pannel. Cut off the old thermostat wires and connect the new wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from SIOUX FALLS, SD
- Parts Used:
- WR60X31522, WR60X46086, WR02X12149, WR02X12008
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
There was frequently a loud buzzing sound that would come from the freezer.
I wouldn't have tried it without the excellent YouTube video that gave step-by-step instructions! I set up a laptop next to the refrigerator and watched each step then did it myself.
The instructions were very detailed and all of the parts looked exactly like what I was seeing. The only difference was that I didn't need to remove the floor of the freezer to get to the fan motor.
I bought the fan motor, grommets (2), compression ring and fan blade because I wasn't sure which part was causing the problem, and figured that as long as I was in there I might as well put in all new parts.
As it turned out, I did not need the compression ring, because the new fan blade came with a compression ring on it. This was different from what was shown in the video.
Since doing the repair the freezer is now as quiet as it should be, which is a great relief. The project and the money spent were more than worth it. It was great not having to pay a repair man to do the work!
The instructions were very detailed and all of the parts looked exactly like what I was seeing. The only difference was that I didn't need to remove the floor of the freezer to get to the fan motor.
I bought the fan motor, grommets (2), compression ring and fan blade because I wasn't sure which part was causing the problem, and figured that as long as I was in there I might as well put in all new parts.
As it turned out, I did not need the compression ring, because the new fan blade came with a compression ring on it. This was different from what was shown in the video.
Since doing the repair the freezer is now as quiet as it should be, which is a great relief. The project and the money spent were more than worth it. It was great not having to pay a repair man to do the work!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from BOULDER, CO
- Parts Used:
- WR60X31522, WR60X46086
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Freezer was wet and there was no air coming out of the freezer fan. Unit was very noisy too.
The video that was attached to the part order was good, but not exactly the same as my unit. One thing I recommend is that you cover up the drain below the evaporator coil with a piece of paper and tape it down, because as I was putting the motor back I dropped a screw and it fell down the drain. So I had to go buy a new screw.
Give the cost of a repair man coming to fix a refrigerator that cost only $450 to begin with, doing this repair was well worth my time. (But I also had another refrigerator to move things to and could take my time and wait while they replaced the faulty part they shipped me.)
Give the cost of a repair man coming to fix a refrigerator that cost only $450 to begin with, doing this repair was well worth my time. (But I also had another refrigerator to move things to and could take my time and wait while they replaced the faulty part they shipped me.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from ORANGE, CA
- Parts Used:
- WR60X31522
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
The fan got very noisy.
My husband did the repair in 45 minutes and said it was very easy. The video made everything plain and simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from COLORADO SPGS, CO
- Parts Used:
- WR17X11889
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
Cracked shelf rails
Removed the cracked rails in the door and snapped the new ones into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from HAYDEN, CO
- Parts Used:
- WR32X10398, WR71X10378
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Crisper Drawer Cover was broken, and i wanted to add a third shelf for my garage fridge
I slid the old crisper drawer cover out, and slid the new one in. Then I respaced the other shelves, making room for the third shelf, and put the new shelf in. Apart from the time it took me to unpack the boxes these parts came in, and to remove my groceries from the fridge, the "repair" itself took all of about 90 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wanda from HOUSTON, TX
- Parts Used:
- WR32X10398
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken crisper drawer cover
After removing all items from the broken top, I removed both drawers and crisper top. I then slid the new top in place and replaced the drawers which easily slid into the grooves in the underside of the top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from TUCKER, GA
- Parts Used:
- WR17X11890
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Missing shelf
Went right on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from WINTERVILLE, GA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lights blown out
replaced lights in refrigirator and freezer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from SHERWOOD, MI
- Parts Used:
- WR60X10348, WR02X10098
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Fan motor was making an intermittent (very annoying) squealing noise.
Located the model number on the inside wall of the unit. Wanted to make sure to order the correct product.Because of the age of the refrigerator I ordered the rubber mounting grommets. In this model the mounting frame is built at an angle that makes the removal and reinstall very easy. Remove two screws and the motor is loose. The fan blade easily pulls off the shaft of the motor . Clean up the fan and reassemble.
Was this instruction helpful to you?
Thank you for voting!