GTH17JBB4RBB General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Randy from VALLEY CENTER, CA
- Parts Used:
- WR02X12008
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Loud whirling noises when the motor started up, then they subside (and stop) in a short time
I have not yet done the repair. After watching this repair video two problems came to mind. First I only ordered one grommet not knowing that there were two (or more I don't yet know). The second problem is that this video must be for a fridge from like the 1940, but it looks NOTHING like mine from 2008. The manual shows a bazillion parts and frankly I'm just a wee bit afraid to get started, and I am generally very handy, buuuttttttttt I don't know about this one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry W. from POTTSVILLE, PA
- Parts Used:
- WR60X31522, WR60X46086, WR02X12008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
fan motor making noise
took old motor out put new motor in and fan blade all done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ted from SANDWICH, IL
- Parts Used:
- WR23X37285
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken light switch
took a little more effort than the video show to remove old module and replace new. Works fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from KEARNY, NJ
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light was flicking
It was way to ez to install only a couple of minutes that's it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicole from Snowflake, AZ
- Parts Used:
- WR60X31522
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Fan quit working
I pulled the shrouding off, unplugged the motor and replaced it. The hardest part is slipping the fan blade off the shaft without breaking it. Works perfectly now. Also, the shipping fed-ex, regular ground was only 3 days here to arizona. Would use anytime
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard E from Oroville, CA
- Parts Used:
- WR60X31522
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Evaporator fan motor went out
After removing 2 screws from freezer air duct and 2 screws and 2 self tapping screws from back panel, I removed all these, as well as the foam duct connector. Checked and verified 120 volts at the motor connector, indicating that the motor was bad. Ordered the motor, and 22 hours later, it arrived. 15 minutes later,and 6 screws reinstalled, it was up and running.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marlys from HAINES CITY, FL
- Parts Used:
- WR17X11662
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Was broke on side
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Eugene, OR
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The door activated light switch was missing.
Pulled the two wires out from the access hole in the lower part of the refrigerator. Put them in the spade connectors on the new switch, and pushed the switch into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Sylva, NC
- Parts Used:
- WR23X37285
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Bad switch for door prevented interior light from coming on
Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of your company & it's repair video. THANK YOU SO MUCH
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Bedford Hills, NY
- Parts Used:
- WR60X31522
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Evaporator motor burned out
No problem, had the job done in twenty minutes,Thanks John
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- hERBERT from Phila, PA
- Parts Used:
- WR60X31522
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
replace evaporator fan
Removed the back of the freezer, 4 screws, and then unscrewed the motor mount with fan and motor attached. Switched fan blades to new motor. Reinstalled motor mounting then back of freezer. I had to go buy the ring opener tool at the auto parts store. $12.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victor from Fort Myers, FL
- Parts Used:
- WR23X37285
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
light in freezer section not working
Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Denver, PA
- Parts Used:
- WR60X46086, WR60X31522, WR02X12008
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The fan motor started making noise
The is my 'refreshment' cooler and sits in our garage. Hotter than heck in the summer so the things runs a lot. Started making a little growling noise. Had to partially disassemble the back panel to get to the fan. Touched the exposed shaft for a second and the sound stopped. OK, it's the fan. Went on line, used the (really great) exploded diagram to figure out what I needed. A couple days later the parts show up. Installed the new fan blade and retainer Removed the old motor (couple of mounting screws), connected the new motor (a plug in) and mounted the new motor making sure the grommet on the front and back were engaged. Turned the unit on and everything worked. Reinstalled the foam channel, the back panel and it ran perfectly. Great support (the diagram), fast delivery and fair pricing. Not bad!
Was this instruction helpful to you?
Thank you for voting!