GSH25GGCEBB General Electric Refrigerator - Instructions

This repair was very simple to do. I cannot say enough about part select dot com. I feel that I am a definite handy man yet the videos on the part select dot com site proved to be valuable. This video showed and reminded me that the plastic bushing holding the auger on was reverse threaded. Being a rightee tightee leftee loossee person embedded in my head I would have worn out that bushing holding the auger in place. I recommend not only purchasing from partselect.com YET please watch the video on this site prior to this installation. This made the installation not only simple yet informative. Thanks!

Turned off power, removed cover from Ice maker, checked resistance across thermostat for zero (read open), all other switches read proper value (when activated). Ordered and received thermostat. Removed Ice Maker from freezer, removed two screws holding ice tray to Control Assembly. Removed Thermostat and replaced with new one. Applied Silicone Sealant to face of Thermostat for adhesion to ice tray when assembled. Remounted Ice Tray to Control Assembly and remounted in freezer. Works Great...

Remove lower front panel, disconnect damaged union from water hose under freezer door, replace with new union, tighten and reattach front panel. No more water coming from under the unit. Ice maker and dispenser features returned to working order!

i used the video it showed on the site or iwould not have been able to do it

Followed video for replacing the ice chute flap solenoid replacement because getting to the ice funnel took same steps of disassemble. Looked at how the existing funnel was set in the housing, where and how one spring was located, where the switch and its activating arm on the ice funnel were located, took old one out and put new one in. Cleaned everything in process.

I replaced that part, but I still have the same problem, no water is dispensed. I believe I may need a circuit board. The problem was not the parts I replaced.

Replaced entire ice bucket and auger assembly (one piece).

First I turned the refrigerator and water line off. Then moved to the freezer section, followed the directions, removed the two screws. Directions state to not remove them but I had to in this case. Unplugged the ice maker and removed it from the freezer. I installed the two mounting screws then tried to plug the electrical connection back in but had to use the adaptor cord furnished in the kit. The cord was a little long but I tucked it in and mounted the ice maker. Turned it on then turned the refrigerator and water back on and in a few hours had ice! Very easy to do!

Removed the ice tray and then the auger unit from the tray assembly. To accomplish auger removal, the auger assembly is attached to the tray assemble at the front. On the front bottom there two screws. Back them out. Then on the top of the tray assembly the auger assembly is held in position by two tabs. Depress them with a finger or thumb. Do not use a screw driver as this may result in breaking the plastic tab! The auger assembly will separate. The crusher plate easily separates from the auger assembly and is removed buy "spiraling" the plate up and off the auger itself. Simply reverse to install new plate.
Recommendation: Take this opportunity to thoroughly clean and COMPLETELY DRY all components prior to re-assemble and re-install into the refrigerator.

Part arrived in 2 days and took about 15 seconds to install. Great!! No more broken eggs!!

I downloaded a schematic of the ice dispensing unit. The whole unit pulls out and there are a couple of screws that remove plastic covers. The "trick" was to get the two plastic tabs pushed in and lift the auger unit out of the tray - a two person job! We used knife blades (it was the thinist and strongest tool around) to push the tabs in and pry the auger assembly out. I think we did a great job NOT breaking the plastic pieces! As careful as I was, I definately needed the schematic to put the ice crushing blades and spacers back together. All of this could be avoided if they used a metal auger instead of plastic!

removed 3 screws unplug and remove old unit. install two screws install new ice maker, tighten screws plug in and turn on. had ice in 20 min.

Just look at the parts diagram and follow the explanation. That easy. Still not dispensing water, so i think i need a switch since the water filter is new but no water.

First turn off the power, remove the ice tray, remove the two screws holding the ice maker to the side of the freezer, use the screw driver to gently open the electrical clip for the power cord inside the freezer, remove the complete unit from freezer, bend the old stripper from the holding pin- it is flexible- it will bend, replace the new stripper on the holding pin and bend into the slot to hold it firmly, no water will come out from the fill cup into the freezer, plug in the power cord, mount back to side of freezer, you are done.

Ice maker assembly removed from refrigerator and disassembled. Note nylon nut holding the Augur in place is removed clockwise. As you take the assembly apart, note each piece for reassembly.