GCE24KBBAFSS General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Debra from Norfolk, VA
- Parts Used:
- WR71X10764
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Shelf broke
I just snapped in the new side to the shelf ...very simple and easy:-)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert J. from Darlington, SC
- Parts Used:
- WR71X10764
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Broken shelf insert
Snapped it into place. Nothing to it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cyndy from Rancho Cucamonga, CA
- Parts Used:
- WR23X31507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
I dropped one of the trays and it hit the light switch and broke off!
It was so darn easy! Took less then 10 minutes to fix. Self explanatory no instructions needed! Very cool!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Littleton, CO
- Parts Used:
- WR23X31507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The Light Would Not Go On
Knew the switch was bad. Researched on the internet how to fix. Used a steak knife to pop the old one out, changed the contacts to the new switch and popped it back in. It took longer to open the box than it did to replace the switch. And the part arrived 2 days after I ordered it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Shelton, CT
- Parts Used:
- WR82X10103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
brand new ge refrigerator delivered with broken access cover. cost 6.95 so i repaced it myself.
removed 6 screws and repaced cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from auburndale, FL
- Parts Used:
- WR71X10764
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken door bin
looked up the part on your site which was very quick and easy. Ordered the part and it came quickly and my installation was just as quick. Greatful for your web site Regards John
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from GROVELAND, FL
- Parts Used:
- WR02X10821
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Slide control was broken
Simply slide new control slide through slot from front.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from MATTAPOISETT, MA
- Parts Used:
- WR71X10764
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Clear front plastic cracked
We were able to easily remove the existing clear section of the door shelves and replace them with the part we ordered from partselect.com. We needed to contact customer service during the order – they were efficient and friendly. The parts came quickly and were easily installed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from MOUNT VERNON, IL
- Parts Used:
- WR71X10973
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The bottom was cracked
Just replaced it with new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Monica from RENO, NV
- Parts Used:
- WR71X10764
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
plastic on front of shelf had been broken for FOUR years
repair (replacement of the broken piece) took less than 2 minutes. I can't believe I waited so long to fix this. Piece was expensive, especially after shipping costs -- but now it looks brand new so I am happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from PALMYRA, VA
- Parts Used:
- WR23X31507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The switch was loose ( no spring). The lights did not work.
Unplug the refrigerator. Gently pry old switch out with screw driver. Move wires to connector on new switch with needle nose pliers. Pop it back into the hole. Plug back in. Peek inside to see the lights working.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Vacaville, CA
- Parts Used:
- WR12X10626
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken shelf face
+The shelf face has little plastic locator clips that snapped off. the shelf face just comes off with a light lift of these two clips and a slight upward pull then lift up and off. The new one slips on with the top slipping onto the top rail of shelf, then push the bottom tow clips over the bottom rail of the shelf. There you have it smooth as glass.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Trevor from ALAMOGORDO, NM
- Parts Used:
- WR60X10307
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Motor stopped due to corrosion
Uncovering the motor is the most difficult part. Installation is stupid-easy. Put all of the coverings back on in reverse order to the way they were removed. I don't think the ice maker has to come out but we weren't using it so it came out first.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Escondido, CA
- Parts Used:
- WR02X12008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Fan making noise.
Remove ice maker and all of it's accessories in order to remove the panel covering the fan. Don't drop the screws!
Unscrew the lower fan bracket. You will see the lower red rubber grommet. Hold fan motor with one hand and push the fan off the shaft and into the compartment above. Then remove the round retainer thing below it by holding it and pulling down on the motor assembly. Install new grommet on upper part. and put it all together.
REMEMBER where the fan is on the shaft. It has about one inch of shaft placement. I put mine so that most of it was above the hole that the fan goes into and about 20 percent showing below the sheet metal.
Also check to see if your fan is damaged. Mine was not.
This refrigerator has been awesome! I have had many issues but have been able to fix all of them for the last 15 years!
Unscrew the lower fan bracket. You will see the lower red rubber grommet. Hold fan motor with one hand and push the fan off the shaft and into the compartment above. Then remove the round retainer thing below it by holding it and pulling down on the motor assembly. Install new grommet on upper part. and put it all together.
REMEMBER where the fan is on the shaft. It has about one inch of shaft placement. I put mine so that most of it was above the hole that the fan goes into and about 20 percent showing below the sheet metal.
Also check to see if your fan is damaged. Mine was not.
This refrigerator has been awesome! I have had many issues but have been able to fix all of them for the last 15 years!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from GREENSBORO, NC
- Parts Used:
- WR02X12008
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Fan was not centered in the middle of the back panel opening.
Bent the motor bracket down, then using a rat tail file, elongated the holes in the back panel of the refrigerator to secure the fan in the "centered" position. This was a problem that was with the refrig. since it was made. The parts involved were perfect. NO problem at all installing them.
Was this instruction helpful to you?
Thank you for voting!