ETS22SBPARBS General Electric Refrigerator - Instructions

First I removed the ice tray rack lifting it out of the way to reach the back cover of the fan. Then, the whole back inside panel had to be removed. Two screws removed the fan and bracket from the freezer unit. The missing bumper lid just snapped into place. Replaced everything in reverse order. Pretty easy job.

Replaced both the Defrost Thermostat and Defrost Heating Element. The You Tube repair video clips were extremely helpful for both operations. My difficulty was getting access to the parts that needed to be replaced in a very tight side by side freezer space. Otherwise, the repair went smoothly and the refrigerator is back in normal operation in time to save the perishable food inside.

You guys ought to win some sort of website Emmy. I found your site as I was searching for a new motherboard, thinking this was the cause of the temperature control problem. I took the time to go through the little diagnostic process you offer and I discovered that the much less expensive defrost thermostat was more often the root cause of the problem ($8 vs $160 for the new motherboard). The part arrived within 3 days and the installation video was enormously helpful. Removal of the rear panel was more difficult than suggested on the video. I'd suggest removing the freezer light fixture before trying to remove the panel as it is nearly impossible to bend the metal panel around the light bulb bases. Anyway, the whole job cost me about $16 for parts and delivery and the fridge is running fine. The combination of the diagnostic tool and the installation video were fantastic...far beyond expectations.

This was generally an easy fix. The work was in such a confined area of our side by side and my husbands shoulders are broad so that was a little more challenging but overall a quick, easy and cheap repair doing it ourselves without having to call a appliance repairman.

Disconnected the refrigerator for a few hours. On back of frezer compartment unscrew 4 screw to get access to Old defrost thermostat (D. T.). I cut the two wires with pliyers atached to D. T. Peel them about one inch both the old and new D. T. With plyier. Color coded put them together. I used those electrical cap wires to attach them toguether an electrical tape around it to prevent any moisture. Now working like new. Expend approximately $25. And 20 minutes of my time. (I was being charged for the repair. $250.) Now is working like new. Thanks

Remove the top cover above the door by lifting it slightly and pulling forward. I used a mirror to make sure that there was nothing in the way of accessing the switch from above. I used a blade screwdriver to press against the switch retainer on the topside, while GENTLY prying from below with another blade screwdriver to get the switch dislodged. Once the retainer was past the opening, I wiggled the switch downward and then rotated it to the left when the rounded top right edge of the switch was visible. This allowed the wiring to the connector to pass thru the hole. I pushed the wiring from the top and pulled from below to get the connector below the opening for the switch. I then unplugged the switch, plugged in the new switch and reversed the removal process feeding the connector thru first then rotating the switch to the right to get the rounded edge of the switch thru the opening, then pressed the switch up into the opening until it snapped into place. Total time less than 10 minutes.

I removed the top shelf and then the existing slide. I replaced the slide and then the shelves.

The only hitch was the need for a special screwdriver which cost $5.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

As per the video , I unplugged the appliance and defrosted the freezer . Then removed the shelves and back from the freezer. Located and removed the old parts and installed the new ones which took about 20 minutes. Reassembled the appliance, plugged it in and it was cold within a few hours. Thanks for all the help

Remove one nut top of ice box cut wire and replace temperature sensor in freezer part remove two nuts on back panel and cut wire and add temperature sensor then remove defrost thermostat cut orange and pink wire and twist together new sensor and tape up and one more temperature sensor add bottom of freezer cut and replace and tape up all wire and replace back cover simple easy job

Replaced Temperature Sensor and now it is getting cold.

I removed the pan with the gliders attached. I used a socket set to remove the broken glider from the pan. Then, I put the new glider on and tightened the socket and put the whole apparatus back in the refrigerator. I am a 75 year old woman and had no trouble doing this myself.

Needed a square head screw driver.
Appliance man wanted $80 to come out plus parts. Part cost $20 and took 10 minuyto out on. Had to empty half the refrigerator. That took longer than the time to fox

Extremely easy repair, the hardest part was getting the old switch out. I used a pair of needle nose pliers to squeeze the tabs in and it came right out.

put the gratefruit knife behind the old switch pooped it out pluged the new one in piece of cake 5min.even vacumed the dust off the coil