GTS17BBMBLAA General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Wendy m from BROWNINGTON, VT
- Parts Used:
- WR60X31522
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
freezer was too warm, only froze ice cubes on the bottom, fan making noise, food only stayed froze if already frozen
followed instructions in the video. simple tools. pretty easy. Most people would have just bought another refrigerator, $50.00 was much better. Is working just like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from Santa Ana, CA
- Parts Used:
- WR02X12149, WR02X12008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Loud Sound In Freezer
I followed the video for my model refrigerator on parts select. My hint: when returning the back panel of the freezer, it's slightly adjustable left and right to avoid grazing the fan.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from BRADLEYVILLE, MO
- Parts Used:
- WR23X37285
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Broken light switch
This was so easy I think it took me 2 minutes. I am not very mechanically inclined but that didn't matter! Works perfect thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eleanor from OREFIELD, PA
- Parts Used:
- WR32X10398
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Simple
Removed old one lined up drawers, wonderful, great company to buy from and do business with, thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THOMAS from MEBANE, NC
- Parts Used:
- WR60X10168
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Noisy Fan Motor
Simple. Rolled the refrigerator out , unplugged the 120 volts AC outlet.(1) Unplugged the wiring from the cabinet to the fan (white (three pin connector)). (2) Removed the two 5/16 inch screws holding the rear motor bracket . (3) Removed the fan blade from the motor shaft by applying slight pressure, pulling if off the old motor shaft. (4) removed the rubber isolator from the frame and from the rear of the old motor. (5) placed the rubber isolators back on the motor and frame. (6) Pushed the new motor back into the frame and re-installed the fan assembly. (7) remounted the fan with the rear support and the two 5/16 inch screws. Reconnected the three wire connector. Just checked the fan blade assembly to make sure they were not hitting the fan shroud. Fan blades should sit just partially inside the shroud to make sure it produces maximum airflow.
(8) Reconnected the 120 volt AC and waited for the compressor to cycle back on... Nice quite fan... Thanks
(8) Reconnected the 120 volt AC and waited for the compressor to cycle back on... Nice quite fan... Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- merlin from TRENTON, NJ
- Parts Used:
- WR32X10398
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
cover was cracking on sides
removed bins ......removed cover .....replaced with new cover....replced bins back .....done !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janice from LORENA, TX
- Parts Used:
- WR32X10398
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Crisper drawer cover was missing
I simply slipped in the new drawer cover and put the drawers in. So easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maureen from LYNCHBURG, VA
- Parts Used:
- WR60X31522
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Refigerator was amking a loud noise when the fan came on to cool.
Followed the on line instructions and found the repair to be very easy. Took longer to remove the food from the freezer than to switch out the fan motor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from DEPEW, NY
- Parts Used:
- WR60X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Broke fan blade cleaning unit
Ordered part came in 3 days. Removed plug and rear cover. Pulled off old fan . Installed new fan by pushing it on to shaft. Plugged unit back in to check operation, installed rear cover. Done. Part fit perfect. Thanks to this site you folks are great !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from PARKVILLE, MO
- Parts Used:
- WR02X10098
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Had a 'ticking' sound
Separately (from a different site) purchased new compressor fan and motor. I purchased the grommets here because the other site listed the grommets as temporarily out of stock. I did watch one of the videos on PartSelect about the grommet replacement. Repair was pretty simple, biggest challenge was getting to the screw on the far side of the motor. Removed the two screws holding the fan motor into place. Removed motor and blade. Reinstalled with new fan blade, new grommet and new motor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from BAKERSFIELD, CA
- Parts Used:
- WR60X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Old fan had broken blade, needed to be replaced
Unplugged the refrigerator then used the cordless drill to remove the 6 screws on the access panel on the back of the fridge to be able to get to the fan. Was able to pull the fan off by hand and push the new fan on by hand. Plugged the refrigerator by in and watched the fan run for a few minutes then replaced the access panel. Really quick and easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from NEW YORK, NY
- Parts Used:
- WR60X31522
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Noisy motor that was getting worse.
Followed the steps on the linked video. Absolutely accurate and easy to follow. Beware: Don't drop a screw down the opening after removing the styrofoam block.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from GAINESVILLE, FL
- Parts Used:
- WR60X31522
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Noisy fan in freezer compartment
First I unplugged the power. Then I removed the wire shelf, center plastic cover, flited the stryofoam piece out, removed the back panel. Then I disconnedted the fan connectors. Then I took the fan brackets off and removed the clamp holding the fan blades to the motor shaft. I then reversed the steps to complete the installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Escondido, CA
- Parts Used:
- WR02X12008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Fan making noise.
Remove ice maker and all of it's accessories in order to remove the panel covering the fan. Don't drop the screws!
Unscrew the lower fan bracket. You will see the lower red rubber grommet. Hold fan motor with one hand and push the fan off the shaft and into the compartment above. Then remove the round retainer thing below it by holding it and pulling down on the motor assembly. Install new grommet on upper part. and put it all together.
REMEMBER where the fan is on the shaft. It has about one inch of shaft placement. I put mine so that most of it was above the hole that the fan goes into and about 20 percent showing below the sheet metal.
Also check to see if your fan is damaged. Mine was not.
This refrigerator has been awesome! I have had many issues but have been able to fix all of them for the last 15 years!
Unscrew the lower fan bracket. You will see the lower red rubber grommet. Hold fan motor with one hand and push the fan off the shaft and into the compartment above. Then remove the round retainer thing below it by holding it and pulling down on the motor assembly. Install new grommet on upper part. and put it all together.
REMEMBER where the fan is on the shaft. It has about one inch of shaft placement. I put mine so that most of it was above the hole that the fan goes into and about 20 percent showing below the sheet metal.
Also check to see if your fan is damaged. Mine was not.
This refrigerator has been awesome! I have had many issues but have been able to fix all of them for the last 15 years!
Was this instruction helpful to you?
Thank you for voting!