PSHF9PGZBCBB General Electric Refrigerator - Instructions

using a small socket wrench and star shaped driver I (1) removed the two screws that held the broken stop from the bottom of the door, and (2) replaced the new stop and screwed it back in. The most difficult part of the job was opening the door in order to access the second screw.

Unfortunately, the replacement part didn't come with instructions. The repair, nevertheless, was fairly straightforward. After removing the plastic parts that guide the ice through the door (by removing a few screws that attach the parts to the inside of the door), I was able to slip my hand into the ice maker dispenser and remove the old part. The part clips on. It is a tight fit through the funnel (from the outside of the freezer), however, and requires that the gasket first be "flipped" open wherein it unfolds 180 degrees. Doing this will make it easier to clip the new gasket onto the assembly.

I first replaced in-line water filter to the fridge. No ice. Then I replaced the water filter inside the fridge. Still no ice. I inspected the water inlet feeding the ice cube trays and it was froze up with ice. I removed the two screws holding the ice maker in place to remove the ice from the inlet tray. I then used a hair dryer to melt the ice accumulated in the in-coming water tube. Turned off the water and unplugged the fridge. When replacing the old water valve, I first blew through the hose feeding the ice maker to be sure that it was clear of ice. After re-attaching the water hoses and the electrical connections, I turned on the water, plugged in the fridge and turned the ice maker switch back on. Next morning I had ice cubes. Only mystery is I am not hearing the usual water noise when water is feeding the cube tray like I did before, - not to worry though if it works. My drawer is now full of cubes.

Ordered the new part (water valve). Took off the bad one followed directions on you video. The video explained the process making it easy to do.

I received part. I then used a hair dryer to smooth out kinks. Took about 15 minutes. Pulled off old gasket and replaced with new one. Used hands only.

First, I removed the top drawer blocking the area where I needed to put the glass panel cover. Then, I removed the drawer along with the glass panel holder to which I needed to install the glass. I installed the glass to the panel holder without difficulties (although the glass cover was expensive :() and reinstall the drawers back to their proper place. This repair was actually a no-brainer.

Suggest removing black plastic grill first to gain better access to door stop screws. The grill is attached by two phillips screws, one on either end and several metal spring clips in the middle. The door stop is held by two star shaped screws that are only visible with a mirror. Suggest using a bit attached to a small ratchet.

Removed panel from front of freezer door by pushing up on three spring loaded screws located in the opening where the ice door opens and closes. they are about 1 inch apart on the bottom of the opening. Push up to free ice maker panel. Remove three screws from solenoid, located at the top right. Remove wire, replace with new and that is it. Fixed the problem!! Our ice maker hadn't worked for months. Be careful if you remove the round ice maker door to clean. There is a spring that located on the left side of sprocket. The spring fell off and took me a while to figure where it came from. Recieved package in three days and the job took minutes. Works great! Very easy to complete.

1. Removed all food, shelves, and ice bin from freezer compartment.
2. Removed freezer light hood and unscrewed freezer bulb.
3. Removed rear evaporator cover panel (2 Phillip’s screws, 2 hex screws).
4. Melted ice on coils with hair blow dryer (needed bath towels to collected water).
5. Removed old defrost heater (2 Phillips screws, 2 plug-ins).
6. New heater connected without any adjustments.
7. Replaced evaporator cover ice bin, shelves and food.

The repaire guy came in tooke it out and told me it is goin to coast $20 for the part and $50 for the labor..... So I looked, It was soooo eeezzz ALL you have to do is get the switch out( with help of my butter knife :) it plugs in to a little outlet on the wire (on the botom side) so take out the old one and plug in the new one wich I got for $8 + $6 shipping = $15 THANK YOU PART SELECT for saving me $55 Im a 36 y/o stayathome mom and Ihave never don this before, Im very proud of my self. well... it was very easy!

took back panel off in freezer.unpluged unit then cut wire to sensor tie in new one wire nut them up and taped.on the heater strip took off two screws and unpluged two wires put the new in same way as taking old one off.I am pleased that the parts from part select came as fast as they did I would for sure buy from them again and prices were very fair.Thank you very much for your service.

Level of difficulty, as far a mechanical skill goes is relatively easy; however, everything in the interior of the freezer (including icemaker) must be removed to get to the defrost thermostat. The defrost heater only needs the racks and back panel removed. It probably took about 45 minutes with a heat gun to melt the ice off of the coils so that I could work on it-need lots of towels/rags to pick up the water.

After removing three screws on the ice bucket, it basicly came apart by itself. I needed to use pliers to remove the old nut because it had over tightened itself onto the shaft. Be careful here - it is a left hand nut - not a normal right hand nut! Reassembly was a snap putting the parts back together in reverse order. Unit has been working great since the repair.

By reading another customers tip I decided that my problem was the exact same. I had to order the entire motor not just the auger because the motor shaft was stripped. Once you remove the motor, hold the shaft with a pair of vise grips and use a screw driver to turn the auger off clockwise. The threads are reversed. The new auger screws easily onto the new motor counterclockwise and installing back into the fridge was a snap.

Replaced both temp sensors worked good for 2 days then began freezing food. Looked into it further on line. Found small motorized door broken that controls the cold air from the freezer