PHE25TGXBFBB General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jim from SPANISH FORT, AL
- Parts Used:
- WR62X10055, WR17X11653, WR17X10706, WR02X10585
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
FROST IN FREEZER NO WATER
FOLLOW INSTRUCTIONS OF YOUR VIDEO
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Rockford, IL
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
heavy frost buildup in ice dispenser chute and door
After inspection of the new door recess assembly, I realized that I could use sidecutters (electronic assembly type) and 'clip' off the inward lock tabs of the old recess assembly and disengage it from the crank door arm without any further disassembly of the refrigerator door. It was easy to 'unhitch' the tang from the crank arm and wiggle it out through the external opening of the ice/water dispenser compartment. I reversed the process and inserted the new assembly through the external opening of the compartment. The new door recess assembly snapped into place on the crank arm and fit tightly against the ice chute opening, correcting the issue caused by aging distortion of the old rubber seal cup portion of the door recess assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Tucson, AZ
- Parts Used:
- WR17X10703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Icemaker wouldnt dispense ice
Took the tray out, removed three screws, popped the front tray out, installed the deflector, and put it back together. Done in less than 15 minutes and my wife is ecstatic that our dispenser works again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rich from san marcos, CA
- Parts Used:
- WR23X21444
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No ice from door, but did have water
I got the wrong switch before so just need to put the right 1 in. Super easy, pop off old, plug in new, click back into place. Done. REALLY REALLY EASY for anyone to do
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Cypress, TX
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Won't dispence ice or water
Changing out solenoid was very easy, but you don't have to remove trim ring and it didn't fix my problem. Turns out a relay fell out of its holder in the piece you have after removing the 4 screws per the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frances from SPARTANBURG, SC
- Parts Used:
- WR12X10625, WR12X10625
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Drawer fronts on freezer needed replacing
New parts just snapped in place. Perfect fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from WALLIS, TX
- Parts Used:
- WR74X10270
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No kickplate on use refrigerator I bought.
I put kickplate on refrigerator and use 2 sheetrock screws and drill to attach. Done in 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stephen from GOODLETTSVLLE, TN
- Parts Used:
- WR23X10783
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
No or little ice would dispense
Went exactly by the video. Perfect job, you send the installation video with the part. You watch the video before or during, goof proof, took longer to disassemble than to replace the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Andover, MA
- Parts Used:
- WR02X13425
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Socket set
Door Stop Broke on the Refrigerator side.
Followed the instructions in the operator's manual to remove the door. Popped off cover of top hinge. Unscrewed the two screws holding pin down with socket set. Took off door. Unscrewed broken door stop with TORX socket. Replaced new door stop and reversed the process to replace the door. Very simple repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from CHARLESTON, SC
- Parts Used:
- WR29X10085
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
The left three tines bind and break off because they don't match the part removing the ice.
The right side of the three left three tines must be shaved about 1/8" to allow the ice remover blades to pass unimpeded.The part should be manufactured better.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from DURYEA, PA
- Parts Used:
- WR55X10025
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
both freezer and refigerator were warm.
I watched the video online and it said there were three sensors in the refrigerator, two in the freezer and one in the refrigerator. I only ordered one sensor and was going to try the one in the refrigerator first. He said the upper one in the freezer is the most difficult, but is usually the problem. So, I replaced the upper sensor and tried restarting the unit. Everything went well and it fixed the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Lacey, WA
- Parts Used:
- WR17X11505
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Icemaker parts were cracked after use
I had to replace the whole tray. Required complete disassembly and reassembly. Simple to do. No problems whatsoever!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from Henderson, NY
- Parts Used:
- WR29X10085
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
ice maker was making no ice.
snapped in the new stripper arm where the defected one was.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryan from Fairfax, VA
- Parts Used:
- WR62X10055
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Freezer frosting up around ice dispenser chute.
Ordered new solenoid so the flap would close. That did the trick.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from SANFORD, FL
- Parts Used:
- WR17X11459
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replace Ice dispensing drive cup
Watched the UTube video on how to replace. Very simple instructions. So easy a 10 year old could do it.
Was this instruction helpful to you?
Thank you for voting!