PFCS1NFZASS General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- charles from SCOTTSDALE, AZ
- Parts Used:
- WR55X10025
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Defrost not working coil iced up
Removed back wall cover over coil. Defrost all ice with a hair dryer. Cut white wires and replaced Temperature Sensor. It has been working for a week and no trouble at this time. If you have this system on your GE refrigerator do this before replacing the motherboard. I must admit I was thinking that was the trouble. Motherboard was replaced after 5 years old now 5 years later my thinking is this a 5 year problem. So try the Temperature Sensor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marie from Philidelphia, PA
- Parts Used:
- MWFP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace filter
just had to unscrew old one put the new one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from AURORA, OH
- Parts Used:
- WR14X10305
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Leaking and split door gasket.
Pull off old gasket and push on new one. It couldn’t have been simpler.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from RINGGOLD, GA
- Parts Used:
- WR49X10283
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
compressor won't kick on
Pulled ice box away from wall. Took lower cardboard cover off. Shut water line off. Got my volt meter and checked the current going from the wall to the plug in at the inverter (input side), and I had the required 115 volts. Then I unplugged the connection going to the compressor (not the plug at the compressor which you cannot see until you unbolt the inverter) but the output connection side that goes to compressor. I checked the voltage and had about 13 volts not the required 115 volts. Therefore, I came to the conclusion that the inverter was bad. I ordered one from Partselect and they shipped it right away. I installed it and the ice box is back up to running order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- martine from LAGUNA NIGUEL, CA
- Parts Used:
- WR14X10305
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Mold and brittle
Super easy. Took off the gasket and replaced with new. Too 5 minutes for both doors
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CATHLEEN from Agoura Hills, CA
- Parts Used:
- WR02X12364
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Dairy door broke off when spouse was unable to shut it due to box of butter inhibiting the door from closing
Removed the entire dairy shelf from door and installed the dairy door and replaced the entire dairy compartment on door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- randall from coopersville, MI
- Parts Used:
- WR55X10025
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
refriderator not cooling consistetly
1 opened door 2. pryed cover off from cieling 3.cut and stripped wires on 4. sodered wires from old wires to new sensor. 5 insulated conection.6 put cover back on. This did not fix the problem it was the control moduel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Coto de Caza, CA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Interior Light did not go on due to faulty switch
I ordered two switches, replaced both with a knife in 10 minutes. Interior light works, thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eileen from Coto de Caza, CA
- Parts Used:
- WR23X37285
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
switchlight on my refrigerator was not working
I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, it was just a matter of plugging in the new switchlight , which was very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from CAMBRIDGE, MA
- Parts Used:
- WR17X12456, WR01X10680
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The freezer drawer was over cooling and the upper section had no cooling due to something very sticky spilling onto the damper.
Just pulled apart the lower cabinet assembly and installed new assembly. Not difficult, just take your time so as not to break any of the plastic.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rene from HEBER, CA
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
condenser icing refrigerator warm freezer ok
follow the easy instructions replace 3 temperature sensors cut the wires and crimp them with new sensor and it works like new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from JAMESBURG, NJ
- Parts Used:
- WR60X10277
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
Refrigerator wasn’t cooling, but the freezer was.
Unplugged the fridge.
Took off the freezer door.
Took off the door brackets and the ice machine. Removed the back panel. Unplugging the light and the ice machine were a challenge to get to. Installation of the fan motor was simple. Reverse all the directions, done. Tough part was figuring out what to take off.
Took off the freezer door.
Took off the door brackets and the ice machine. Removed the back panel. Unplugging the light and the ice machine were a challenge to get to. Installation of the fan motor was simple. Reverse all the directions, done. Tough part was figuring out what to take off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAMES from MATTESON, IL
- Parts Used:
- WR57X10086
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Refrigerator ice cube maker stopped making ice cubes
I replaced the water line and the inlet water valve
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from SHAVERTOWN, PA
- Parts Used:
- WR14X10305
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
Need to remove mullion on French door models
Called repair man as I was not certain how to remove mullion part and disconnect wire. He just removed screws top and bottom then disconnected wire. Then slid off mullion. Replacing gaskets was easy with mullion removed. Rep said NOT to use vasaline as it degrades gasket but rather use a candle if desired. Rep did not use anything just pressed gaskets into empty slot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paula from WESTON, FL
- Parts Used:
- WR72X10218
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
End that holds clear cover snapped off,
Remove glass, lift cover up in front, slide out, transfer parts seals and switch for crisper(one pivot screw. Remove rear seal by using finger nail to pull at gasket slowly pulling it back. Take your time. Reinstall cover and glass, snap pivoting cover back on.
Was this instruction helpful to you?
Thank you for voting!