PDCS1NCYCLSS General Electric Refrigerator - Instructions

Just pulled apart the lower cabinet assembly and installed new assembly. Not difficult, just take your time so as not to break any of the plastic.

follow the easy instructions replace 3 temperature sensors cut the wires and crimp them with new sensor and it works like new

I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, it was just a matter of plugging in the new switchlight , which was very simple.

I made my wife fix it.

Checked water inlet tube inside freezer, stuck screwdriver in it to see if there was any ice and it seemed clear. Checked water pressure to fill valve, good pressure. Replaced fill valve, still no water to ice maker. Replaced Ice Maker. Still no water to Ice Maker. Removed freezer back panel, hit fill tube with heat gun after allowing freezer to defrost awhile, replaced back panel, ice maker. Water going to icemaker fine. Problem was that the fill tube was frozen up way at the back where the water line emptys into the icemaker fill tube. Old icemaker and fill valve were probably OK. No real way to check it from outside the case in the rear of the fridge as the water line is sealed on the fill tube and heating it without removing the rear freezer panel does not get back far enough to melt the ice.

I replaced the water line and the inlet water valve

Replaced evaporator fan motor, and this solved the whistling noise that had developed. Reviewed and followed the removal and installation instruction video as closely as possible. This was very helpful, with a few additions. For the model PS123NGPBBB GE refrigerator/freezer, there were a few differences from the video. There a was an additional cover panel that was positioned vertically at the back of the freezer compartment below the auger motor assembly. It was necessary to remove this cover (4 screws) to gain access to the auger motor cover screws. The unit also has a different light configuration with 2 lights. I found it helpful to remove these light bulbs and the corresponding light fixtures in order to remove the evaporator motor assembly. As mentioned in the video, it was necessary to cut the 4 wires from the wire harness of the new motor, and use butt end connectors to reattach these wires to the corresponding wires in the unit. Total job took between 1 and 2 hours, and the motor change solved the noise problem.

Remove glass, lift cover up in front, slide out, transfer parts seals and switch for crisper(one pivot screw. Remove rear seal by using finger nail to pull at gasket slowly pulling it back. Take your time. Reinstall cover and glass, snap pivoting cover back on.

I watched the video online and it said there were three sensors in the refrigerator, two in the freezer and one in the refrigerator. I only ordered one sensor and was going to try the one in the refrigerator first. He said the upper one in the freezer is the most difficult, but is usually the problem. So, I replaced the upper sensor and tried restarting the unit. Everything went well and it fixed the problem.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

replaced lights in refrigirator and freezer

I got the wrong switch before so just need to put the right 1 in. Super easy, pop off old, plug in new, click back into place. Done. REALLY REALLY EASY for anyone to do

I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.

Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $120 service call.

removed 6 screws and repaced cover.