PHE25YGXAFBB General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Randy from WALLIS, TX
- Parts Used:
- WR74X10270
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No kickplate on use refrigerator I bought.
I put kickplate on refrigerator and use 2 sheetrock screws and drill to attach. Done in 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stephen from GOODLETTSVLLE, TN
- Parts Used:
- WR23X10783
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
No or little ice would dispense
Went exactly by the video. Perfect job, you send the installation video with the part. You watch the video before or during, goof proof, took longer to disassemble than to replace the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Cypress, TX
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Won't dispence ice or water
Changing out solenoid was very easy, but you don't have to remove trim ring and it didn't fix my problem. Turns out a relay fell out of its holder in the piece you have after removing the 4 screws per the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from SANFORD, FL
- Parts Used:
- WR17X11459
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replace Ice dispensing drive cup
Watched the UTube video on how to replace. Very simple instructions. So easy a 10 year old could do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Colleyville, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No water through door dispenser
Replaced flapper valve per website instructions. GE factory technician took two weeks to get here, charged over $100 for the call and told us we needed a new refrigerator door at a cost of over $500 to fix the problem. We sent him packing. After visiting the PartSelect website, the $5.88 PartSelect flapper valve fixed the problem. Amazing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cyndy from Rancho Cucamonga, CA
- Parts Used:
- WR23X31507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
I dropped one of the trays and it hit the light switch and broke off!
It was so darn easy! Took less then 10 minutes to fix. Self explanatory no instructions needed! Very cool!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Shelton, CT
- Parts Used:
- WR82X10103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
brand new ge refrigerator delivered with broken access cover. cost 6.95 so i repaced it myself.
removed 6 screws and repaced cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from auburndale, FL
- Parts Used:
- WR71X10764
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken door bin
looked up the part on your site which was very quick and easy. Ordered the part and it came quickly and my installation was just as quick. Greatful for your web site Regards John
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benjamin from Goldsboro, NC
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice flap in door wouldn't close
Take the face (the part with the buttons on the outside) off, disconnect wired connectors (three), take the screws out of the part behind that (4), and then find the solenoid value (on the right). It's attached with three screws. Mine was rusted beyond belief. I knew this was the problem, ordered a new solenoid valve, put it back in place with three screws (use new screws that fit, not the old rusty ones if possible). When testing, make sure you give the flap a couple of seconds to close. There is a delay, and I initially wasn't patient enough so I had to disassemble and assemble an extra time because of this.
Simply put: If your solenoid value is rusted and the value won't operate smoothly, order the part and install it. This is as easy as any repair could be.
Simply put: If your solenoid value is rusted and the value won't operate smoothly, order the part and install it. This is as easy as any repair could be.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shelly from WATERLOO, IN
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The ice flapper would not go close .
remove the front of were the ice and water comes out
then un scerw 4 scerw and the solenoid slides out unhook the wires and put the new one in
then un scerw 4 scerw and the solenoid slides out unhook the wires and put the new one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from Norfolk, VA
- Parts Used:
- WR71X10764
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Shelf broke
I just snapped in the new side to the shelf ...very simple and easy:-)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ned from Goleta, CA
- Parts Used:
- WR74X10270
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Grill broke removing refer for flooring
Easy order, fast delivery, two screws, done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert J. from Darlington, SC
- Parts Used:
- WR71X10764
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Broken shelf insert
Snapped it into place. Nothing to it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Littleton, CO
- Parts Used:
- WR23X31507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The Light Would Not Go On
Knew the switch was bad. Researched on the internet how to fix. Used a steak knife to pop the old one out, changed the contacts to the new switch and popped it back in. It took longer to open the box than it did to replace the switch. And the part arrived 2 days after I ordered it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from Henderson, NY
- Parts Used:
- WR29X10085
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
ice maker was making no ice.
snapped in the new stripper arm where the defected one was.
Was this instruction helpful to you?
Thank you for voting!