PDSS0MFXBLSS General Electric Refrigerator - Instructions

You guys ought to win some sort of website Emmy. I found your site as I was searching for a new motherboard, thinking this was the cause of the temperature control problem. I took the time to go through the little diagnostic process you offer and I discovered that the much less expensive defrost thermostat was more often the root cause of the problem ($8 vs $160 for the new motherboard). The part arrived within 3 days and the installation video was enormously helpful. Removal of the rear panel was more difficult than suggested on the video. I'd suggest removing the freezer light fixture before trying to remove the panel as it is nearly impossible to bend the metal panel around the light bulb bases. Anyway, the whole job cost me about $16 for parts and delivery and the fridge is running fine. The combination of the diagnostic tool and the installation video were fantastic...far beyond expectations.

This was generally an easy fix. The work was in such a confined area of our side by side and my husbands shoulders are broad so that was a little more challenging but overall a quick, easy and cheap repair doing it ourselves without having to call a appliance repairman.

take the metal cover off the defrost thermostat is on top of the coil take the thermostat off from the coil cut the two wires take the wire and strip the ends off take the new thermostat the wires are color coded wire them together put the thermostat back on coil your done real easy

WE (WIFE) took out the old parts an replaced with new one ..Be careful to get the placement of the Grommet or they "POP" out on you. fast ship on the parts too.

Took out freezer rack took off the back panel also light bulb found the DEFROST THERMOSTAT cut the 2 wires remove the thermostat strip the wires on the new thermostat splice the to wires together with wire nut wrapped wire nuts with electrical tape put new thermostat back were the old came off of put panels back in place also the racks and bulb plunged in the power and guess what it works like a Champ with in 1 hour making ice and going through defrost cycle nice Thank You Guys for your video and the how to do Thanks Ken

Per vidios

After turning off power and unthawing back cover so I could remove it. Then I had remove all of the ice from the coils with a hair dryer. After everything was unthawed I removed the temperature sensor from the coil tubing and cut the wires. I skinned the wires on the new sensor and crimped a butt splice on each wire. I skinned each wire in the freezer then crimped butt splices to each wire. After taping the connections with black tape I reinstalled the back cover and turned on the power. So far it has been two weeks and there Is no frost and the refridgerator is working fine.

I followed your video and completely dismantled the refrigerator evaporator motor, fan, brackets, and grommet, I completely cleaned the refrigerator including the cooling coils. I then ordered the evaporator motor ,fan, grommets, lid bumper, and brackets. The order would take a week to arrive. In the meantime I cleaned and reassembled all the old parts, waiting for the new ones to come. Guess what! The refrigerator was quiet as a mouse. I really did not need the new parts, but I kept them anyway just for good luck. Not bad for a refrigerator that's twenty four years old.

After unplugging the refrigerator-freezer and emptying out the contents I snipped off the refrigerator thermistor, stripped off the wire insulation and used a butt splice. That did not solve the problem. So, a day later I unplugged the refrigerator again, transferred the freezer contents to a newly purchased small freezer unit, took off the back panel inside the freezer portion, and saw a large amount of ice build-up on the silver coils inside. This ice was quickly melted off using a hair dryer and packing towels below this accumulated ice. Then I snipped off the two freezer thermister sensors and the defrost sensor. I soldered the wires together for a hard splice, wrapped the individual wires with rubber electrical tape, and then wrapped that with plastic electrical tape. After re-assembly, the refrigerator-freezer has been working flawlessly for over a week at optimal temperatures.

Unscrewed the mounting screws removed the old grille put new grille in place and installed and tightened screws.

Replaced Temperature Sensor and now it is getting cold.

Remove one nut top of ice box cut wire and replace temperature sensor in freezer part remove two nuts on back panel and cut wire and add temperature sensor then remove defrost thermostat cut orange and pink wire and twist together new sensor and tape up and one more temperature sensor add bottom of freezer cut and replace and tape up all wire and replace back cover simple easy job

As per the video , I unplugged the appliance and defrosted the freezer . Then removed the shelves and back from the freezer. Located and removed the old parts and installed the new ones which took about 20 minutes. Reassembled the appliance, plugged it in and it was cold within a few hours. Thanks for all the help

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Disconnected the refrigerator for a few hours. On back of frezer compartment unscrew 4 screw to get access to Old defrost thermostat (D. T.). I cut the two wires with pliyers atached to D. T. Peel them about one inch both the old and new D. T. With plyier. Color coded put them together. I used those electrical cap wires to attach them toguether an electrical tape around it to prevent any moisture. Now working like new. Expend approximately $25. And 20 minutes of my time. (I was being charged for the repair. $250.) Now is working like new. Thanks