PDCE1NBWBDBB General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Wendell from Baton Rouge, LA
- Parts Used:
- WR60X24484, WR02X12149
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rat chewed up fan blades in refrigerator at our camp.
We just pried off the fan blades and pushed on the new part. Could not have been easier. The rat has been permanently dipatched and, hopefully, that is that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Zachary from Decatur, GA
- Parts Used:
- WR55X10025
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Fridge was freezing food near the back, adjusting internal temp not fixing the problem
Unplugged the refrigerator first....then on the inside of the fridge, I popped the temp sensor cover off (upper LH side) and exposed the old sensor. I snipped off the old sensor about 3" down from the end and connected the new sensor (which I trimmed down to about 3" long) with some heat shrink wire nuts/connectors. Let the fridge run for a day or so and confirmed the problem was solved! Oh yeah, there was no way to tell the 2 wires apart (power vs. ground) on the sensor. However there was a manufacturer's stamp on the wires. So note the orientation of the text and mark one of the wires with a sharpie on both the old and new sensor before trimming. This will give you a reference for which wires to connect when adding the new sensor to the old wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- philip from cocoa, FL
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
freezer would not defrost
There were only 3parts listed to check omed out the defrost heater and thermostat ....thermistor checked bad ordered replacement took less than 2 minutes to replace after I defrosted it again runs fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from San Bernardino, CA
- Parts Used:
- WR12X10850
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken handle
snapped right in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Watsonville, CA
- Parts Used:
- WR49X10211
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Closed freezer with too much stuff in it - broke icemaker support bracket
Did a Google search, found PartSelect.com. Their website made it easy to identify the broken part and order a replacement. For less than $30 and within a few days, I received the new part and installed it. Saved a large repair bill and didn't have to wait at home for the repair person.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jules from Crowley, LA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
failed light switch
I started removing the switch by prying on the right side with a screwdriver, when it emerged enough I used pliers to finish removing it. I then unpluged rhe wires from the bad switch and pluged them on the new switch and "poped" it into the hole.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Saint Charles, IL
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
refrige ws too cold
as per video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christopher from collegeville, PA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no light in freezer
Connected the 2 wires and pushed in the switch until it clicked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from Seatac, WA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
switch wouldn't come out anymore and turn light on
Gently pry out switch in door jam with screwdriver and pull both connectors off and put connectors on new switch then push switch back into the hole. Looked it up on the internet and video showed how to and also had link to new part, ordered and less than a week later the fridge is bright again. I have an older freezer also and it seems that they all use the same switches. Very Very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Rancho Cordova, CA
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator freezing.
Temp. Sensor was under an egg shaped cover on the left side wall in the refrigerator. Remove the cover, cut the two wires to the old sensor and remove it. Connect the new sensor to the two wires using butt connectors. Replace cover and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from WILLIAMSBURG, VA
- Parts Used:
- WR23X21444
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
light switch in freezer broke
Used small screw driver to pry the top of the switch away from left inside wall of freezer side of side-by-side refrig./freezer; then used pliers to remove the switch; then removed the 3 prong socket and plugged it to new switch and installed it into the inside wall of the freezer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Nesquehoning, PA
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Fridge wouldn't keep temp
My son replaced both temperature sensors and the fridge works great now!!! Like brand new again!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Yonkers, NY
- Parts Used:
- WR49X10211
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Freezer divider broke off its attachment to freezer ceiling
Removed broken plastic attachments still connected to freezer ceiling by screws. Needed to take drawer slide from broken kit to install on new divider kit. Installed new divider kit with screws to freezer ceiling (used a little caulking around each screw as an insulator for screw holes). Installed with a little extra effort the cross bar upon which lower portion of dividerd sits. Installed ice tray and baskets.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from Lyndhurst, NJ
- Parts Used:
- WR02X12149, WR02X12008, WR02X10540
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Unusual noise from freezer.
Replaced above parts and the noise problem was not resolved. Ordered a new motor, fan blade and another set of grommets from PartSelect. The parts were delivered the next day. Took me about 15 minutes to swap the new parts in. It's been 3 days since the repair and the noise has not returned.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from SOUTH CHINA, ME
- Parts Used:
- WR60X10185
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Evaporator fan motor was whistling
Ironically I did this today, as this email request came up asking how it went. I'm not a repairman, I'm a software engineer, and I can't thank this site enough for the step by step videos. With the video to help, this was a breeze, I was nervous as I had to empty all my freezer out onto the living room floor. Once that was done the repair took about 30 minutes. Thank you partselect!!!!! My second time doing business here, and I'll be coming back (well, if something breaks, so let's hope I don't have to).
Was this instruction helpful to you?
Thank you for voting!