GTS18ICSURWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Fr Kerry from Washington, DC
- Parts Used:
- WR22X28065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cracked Dairy Door
PartSelect shipped me the part and it arrived in less than 3 days. It took longer to unwrap the excellent packing than it did to pop the new door into place. Wonderful!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victor from Fort Myers, FL
- Parts Used:
- WR23X37285
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
light in freezer section not working
Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Dahlonega, GA
- Parts Used:
- WR57X10033
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
did not work, not sure what the problem is
water runs in now but still does not make cubes. just keeps dripping until I shut the water off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Rockville, MD
- Parts Used:
- WR72X10086, WR72X10055, WR32X28066
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
install second set pan sliders
Because the kit did not include fasteners, had to use wood screws and superglue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Huntington, NY
- Parts Used:
- WR57X10033
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Ice Maker Water inlet valve installed with the Refrigerator had a stripped threaded connection which leaked
Detached the old part from the refrigerator and disconnected the low voltage quick connect. Also disconnected the water line to the Ice Maker. Reinstalled the new part in the order it was disconnected and re attached the water line feed to the valve threaded connection. Turned water on and no problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph Q from Independence, MO
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Replaced valve to ice maker
had to replace copper water line to valve
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carlin from Willits, CA
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
ice maker wasn't working
removed old valve, installed the new one. ice maker back to making ice.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Riverview, FL
- Parts Used:
- WR02X10740
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
frig door kept slamming into cabinet
took the old stop off put the new stop on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- eduardo from oakland, CA
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
water leaking
i swaped the valve it was very easy, but that did not take care of the proble :(
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from east hanover, NJ
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
refig light did not work
per your instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from St Johns, FL
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench set
water leaking on floor from ice maker valve
Replaced single outlet valve for the ice maker
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from New Sweden, ME
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Ice maker not working
With help from this site, It was one of three things. I thought it might be what this site suggested the most common and it was. the valve in back of refrigerator at bottom. Water comming to it, but not getting past. Ordered part. Was here in a few days. Real easy to change out. A few screw / bolts and one wire that fit only one way. I did have to bend new bracket to make it fit. Now have lots of ice cubes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Painter, VA
- Parts Used:
- WR72X10086
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
broking slide
replace the bar lift top off
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from Atlanta, GA
- Parts Used:
- WR57X10033
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker was not getting water
Ordered the part from "parts select". Removed old part, installed new part by unscrewing the old switch, simply cutting supply hose ...pluging in the new part and re-attaching water supply line. 10 minutes at most.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenroy from Martinsburg, WV
- Parts Used:
- WR60X10205, WR02X10098
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
The refrigerator made a humming/grinding sound
I used the socket set to remove pannel that allowed me to have access to the evaporator fan. Once the fan and it's container was visible, I removed the entire fan container using the socket set. I took the fan out of the container, removed the damage blade and the damaged fan grommets. I then replace the old blade with the new blade and put the fan and the compartment back together. I am not very handy so if I am able to do this, anybody can. Ps. I was very very pleased with the services I received from PartSelect and would encourage others to use them - must admit I was very suspicious at first.
Was this instruction helpful to you?
Thank you for voting!