GTS18ICSURCC General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Trina from Decatur, TX
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker was continuously running water
Googled the problem, came across this site where I learned what needed to be done to fix. Checked the part price, looked just for couriosity at the price from GE, it was WAY more expensive. Ordered the part, it arrived super fast, and shipping was next to nothing. The part came in, I replaced it. I made my husband so proud!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Enterprise, AL
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
ice maker valve not working
replaced valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christopher from collegeville, PA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no light in freezer
Connected the 2 wires and pushed in the switch until it clicked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dwight from Indianapolis, IN
- Parts Used:
- WR71X10702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
new refrigator purchased had no freezer shelf
Shelf easily went in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Redmond, WA
- Parts Used:
- WR24X10186, WR24X10187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The refrigerator and freezer door gasket's were leaking
The repair is very simple, the gasket sits in a channel in the door. Just start with a corner and pull the old gasket out. Once you've removed the old gasket, push the new gasket into the same channel. Make sure you've completely pushed in the new gasket all the way around the door. It's as simple as that. The repair takes less than 5 minutes per door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from San Marcos, TX
- Parts Used:
- WR72X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Snack Pan Slide
2 screws. how easy can i get.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kirk from dayton, OH
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
ice maker was not gettin water
took water line loose at outlet valve to confirm that water was getting to valve. I ordered part and it arrived the next day. It was very simple installation took 10 minutes. Thanks to parts select, Kirk
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carole from Oak Ridge, NJ
- Parts Used:
- WR32X10537
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Shelf above vegetable drawers cracked in middle
Take out both vegetable drawers. Lift back of shelf first then front until you hear the click from both front sides. The shelf should now be loose and you can take fully out. Remove the glass shelf from the plastic frame by turning the shelf over and pulling back and up from the rear part of the glass. Put the glass into the new plastic frame by doing the same technique. Then put the shelf back into the fridge by the resting the shelf down in the correct position and pushing the front of the shelf until you hear the click again on each side. slide the drawers back into place and you are done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from District Heights, MD
- Parts Used:
- WR60X10172
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Noisy evap fan motor
Simply unplug fridge, remove air duct mounted on rear panel, release panel itself, pull fan blade off, disconnect grounding wire, detach fan motor bracket, disconnect wire harness to release fan motor, install new fan motor and reconnect, secure with bracket, reconnect grounding wire, reposition fan blade onto motor shaft, reinstall rear panel and secure screws. Remount air duct and plug appliance back in. This is the second motor that was replaced since 2002. The 1st motor dies after 5-6 years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jules from Crowley, LA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
failed light switch
I started removing the switch by prying on the right side with a screwdriver, when it emerged enough I used pliers to finish removing it. I then unpluged rhe wires from the bad switch and pluged them on the new switch and "poped" it into the hole.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Simpsonville, SC
- Parts Used:
- WR23X37285
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light switch quit working
removed the inside fridge electrical panel and swapped switches
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scot from Newark, DE
- Parts Used:
- WR57X10033
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Water not dispensing into ice maker
Replacement of the single outlet valve kit went very well. But, water was still not dispensing. I checked if the valve was working by taking the following steps after installing the new valve: unplugging the refrigerator, disconnecting the water line from the underside of the new valve (line to the ice maker), putting a container under the valve to potentially catch water, plugging the refrigerator back in to start the cycle of the ice maker (remember that the cycle will start only if the temperature cold enough). I saw that the valve worked by dispensing water for a short period of time into the container. Taking my chances (with my limited experience), I disassembled the ice maker in the freezer and found that the water line was plugged with ice. So, I really didn't need to replace the valve after all. But, I'm glad I gained some experience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Indiana, PA
- Parts Used:
- WR57X10033
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Fridge was not making ice, water running thru ice maker into freezer !
Changed out the valve the water line hooks to in back of fridge and bingo that was the problem , less them 10 min job.
Was this instruction helpful to you?
Thank you for voting!