GTH20JBBARWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Loren from EL PASO, TX
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
40 year old refrigerator brittle light switch fell apart
with a jewelry screwdriver I pried the lock tab in and pulled switch down carefully, the hardest part was that the power wire connector was stuck on good but the pliers and the jewelry screwdriver was its match for a bout 5 minute for one connection a simple pull off prong connection. After the wire connected back to switch it popped back in SNAPP
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from BRADLEYVILLE, MO
- Parts Used:
- WR23X37285
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Broken light switch
This was so easy I think it took me 2 minutes. I am not very mechanically inclined but that didn't matter! Works perfect thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from EAST JORDAN, MI
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Light went out in refrigerator
Pop out switch, pull wires, attach wires to new switch and pop back in. Easy smeasy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TIMOTHY from ROBERTSDALE, AL
- Parts Used:
- WR60X10220
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Frig stopped cooling compressor was very hot fan was not turning.
Remove back cover on frig, unplug wire on fan motor, remove one 1/4 screw from top right corner of fan cage, fan cage will come out with a little twist, take note of tabs on fan cage for reinstall, remove two more 1/4 screws, take care to watch where rubber bushings are located on motor and ground wire location, fan blade will pull off of fan shalft easily, install in reverse. Very simple fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from ORO VALLEY, AZ
- Parts Used:
- WR60X10220
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Condenser fan was having trouble starting
Attempted it on my own with the aid of the video on your site, but could not remove the fan shroud due to additional copper lines that prevented me from getting it out.
Gave up and called an appliance repair guy. He had a novel approach: Don't pull the fan shroud (with motor attached) out, but instead remove one of the screws holding the motor into the bracket, then bend the bracket to get the motor out.
All good until we powered the fridge on again. Now the fan works, but spins faster (and makes more noise than) the original fan.
The repair guy's comment: "I've seen that before with some of the aftermarket fans."
Nice! I'd appreciate getting the right part when I order the part from your website based on my fridge model number.
Gave up and called an appliance repair guy. He had a novel approach: Don't pull the fan shroud (with motor attached) out, but instead remove one of the screws holding the motor into the bracket, then bend the bracket to get the motor out.
All good until we powered the fridge on again. Now the fan works, but spins faster (and makes more noise than) the original fan.
The repair guy's comment: "I've seen that before with some of the aftermarket fans."
Nice! I'd appreciate getting the right part when I order the part from your website based on my fridge model number.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RJ from RIO RICO, AZ
- Parts Used:
- WR60X10220
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Condenser Fan Motor
Laying on my side.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from NEW YORK, NY
- Parts Used:
- WR02X10540
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
noisy refrigerator
I followed your video and completely dismantled the refrigerator evaporator motor, fan, brackets, and grommet, I completely cleaned the refrigerator including the cooling coils. I then ordered the evaporator motor ,fan, grommets, lid bumper, and brackets. The order would take a week to arrive. In the meantime I cleaned and reassembled all the old parts, waiting for the new ones to come. Guess what! The refrigerator was quiet as a mouse. I really did not need the new parts, but I kept them anyway just for good luck. Not bad for a refrigerator that's twenty four years old.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from DINGMANS FRY, PA
- Parts Used:
- WR60X10220
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Socket set
Fan motor stopped turning.
Removed the fan blade then removed the motor. Replaced motora nd Installed fun blade.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from BURNEY, CA
- Parts Used:
- WR02X11331
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Loud Squeal when fan was running
WE (WIFE) took out the old parts an replaced with new one ..Be careful to get the placement of the Grommet or they "POP" out on you. fast ship on the parts too.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from KALISPELL, MT
- Parts Used:
- WR60X10220
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Socket set
Fan Motor Was squeaking and not running up to par
I watched the repair video on partselect's website for the condenser fan motor and realized I could do the repair. The hard part was putting the two screws back on the bracket to mount the fan. (they were not easy to get to with your hands let alone tools) other than that super easy and great experience!
Tom
Tom
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from KEARNY, NJ
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light was flicking
It was way to ez to install only a couple of minutes that's it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rose from Dorr, MI
- Parts Used:
- WR60X30922
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broke the fan blade when replacing the Evaporator motor
Took cover off, pushed blade on, and replaced cover
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ted from SANDWICH, IL
- Parts Used:
- WR23X37285
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken light switch
took a little more effort than the video show to remove old module and replace new. Works fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Eugene, OR
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The door activated light switch was missing.
Pulled the two wires out from the access hole in the lower part of the refrigerator. Put them in the spade connectors on the new switch, and pushed the switch into place.
Was this instruction helpful to you?
Thank you for voting!