GTS18XCSBRBB General Electric Refrigerator - Instructions

Pipes out the glass from existing shelf while in place inside refrigerator. Remove broken shelf. Install new shelf. Clean and replace glass. Easy job thanks to finding the correct part from Part Select!

Removed back panel
Unplugged wires to motor
Removed motor & fan assembly
Attached new fan to new motor
Attached motor to motor housing
Reattached wires
Reinstalled back panel

Replace temperature control. That fixed it. Also, removed plastic bag obstructing air vent in freezer which added performance. Fridge works good now.

I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, it was just a matter of plugging in the new switchlight , which was very simple.

First, remove the cardboard cover on the back, lower portion of the refrigerator.

Next, locate the condensor fan motor assembly and blade. (Right side as you are facing)

Using a pliers, hold the shaft to keep it from turning and prevent damage to the motor. Using a screwdriver, slide the old ring compression on the blade shaft toward the motor (away from the fan blades) to loosen.

Remove old blade from the shaft by firmly grasping the motor shaft with a pliers (to prevent from damaging) and pull the blade assembly off.

Reverse the above steps to attach the new blade.

instalation was very easy - but the part was 3/4 inch to long and a 1/32 inch to wide.Trimmed it with the "faithfull"
Dremel and it works!The instalation part of the "job" was less then 10 min.

Took the bracket out of box and install it like the video showed me..very easy to install..

The icemaker arm disconnected from the metal frame. This caused the icemaker to cycle and the heater to come on and stay on until the plastic parts melted causing a mess and stink. This action melted the ice and then the water fell through the frozen items in the freezer and refreezed in the lower portion. OK, I remover the dead icemaker and tossed it away. I installed the new icemaker and the wiring harness didn't fit right (way to long). I retrieved the old icemaker and removed the wiring harness from it. I removerd the new ice maker and installed the old wiring harness to the new icemaker. I then installed the new icemaker, plugged it in and turned on the power. No water, I ordered the dual solenoid water valve, installed it with difficulty (another story) the turned on the power. I reinstalled the ice bin and found it didn't fit. The icemaker was to low and couldn't be adjusted, 1/4" higher would have been great. I shoved in the bin anyway, I was out of ice for my scotch, and it started making ice.

Replaced icemaker assembly. Only 3 Phillips screws to remove the old assembly. Pretty much an exact swap. Was easy to replace but the connecting cable on the new replacement assembly wasn't very easy to make fit. Had to force it into a location that would be out of the way and allow everything to operate properly. That connecting cable should be more flexible and adapt to the fridge a little more friendly.

Inspected freezer because food was not freezing, getting cold, but not freezing. Noticed fan was not blowing air, but making a little motor noise, like it's trying to turn. Removed cover panel, and found the fan blade rubbing on the panel, fan shaft was worn out and very loose, wobley. That told me the fan needed to be replaced. Found part on the GE Partselect website and ordered the parts via the website order process. This was easy. The parts were shipped quickley and were at my front door the next day. Couldn't believe it. The actual process was very easy: Remove cover, remove bracket holding fan motor, remove and replace motor, re-assemble parts. About 20-25 minutes from start to finish. Freezer is working like it's suppose to.

Replaced temp controller

Just popped them in their slots. Very easy and it made my refrigerator brand new again.. Thank you

I order the small part and installed it myself, it was very easy with "part select". I will refer them and use them in the future. Thanks parts select.

To remove the temp sensor.2 Phillip head screws not remove the cover inside fridge .the temp control knob cover.removed that and unplugged switch.installed new switch.reinstalled cover.

Click shelf into place!